Nearly complete Rostock Mini with all electronics.

My name is Joey and I've been a long time reader on the forums but never posted. I'm an active use on the Printrbot Talk forums as my other printers are Printrbots. So please look me up over there under the same user name (vdubskey) if you have any doubts about this listing. I started a Rostock Mini build a few months ago but need to let it go for some extra cash for the holidays. I can disassemble the printer and leave the three towers assembled, or completely disassemble for shipment. Which ever you prefer. Sorry for grainy pictures!! So this is what is included.

All parts were printed by me with Purple Sainsmart ABS @ 0.2 Layer height.

6 8mm Polished linear rods.
6 LM8UU Linear bearings.
6 608ZZ Bearings.
All M3, M4, M8 Socket cap bolts and nuts for assembly.
3 36T Aluminum pulley's.
GT2 Belts with 3 belt tension springs.
1 PTFE Tube for 1.75mm filament.
2 BSP connectors for PTFE Tube.
6 Carbon Fiber rods with Traxxas rod ends and pivot balls (Assembled)
1 200mm Round silicone heat bed.
3 High Torque 76oz Steppers 5mm shaft extra long wires.
1 0.4 J-Head with heater and thermistor and wires. Brand new never used. (The Ubis hotend in picture is not included)
1 Getech Printrboard with Marlin with mount designed by me

***Also included but not picture are 3 Mechanical endstop switches with wire***

I also have a brand new never used Sanguinololu with ATMEGA 1284P loaded with Marlin and 4 A4988 Stepper Drivers still sealed that is being sold separately.

So all you need to get this going is the plexi glass base and top and a extruder of your choice. The printer is assembled in the pictures using cardboard templates that I cut to make sure all my measurements were correct for the rest of the printer. You can get the DXF file for the base and top pieces from the Rostock Mini WIKI or use my templates for your plexi pieces.

I am asking $575 USD + shipping OBO for the Rostock as a whole. Not going to break up!
I am asking $65 USD + shipping for the Sanguinololu and Drivers.

Paypal or cash locally ONLY.

I am located in Modesto, CA. If you are local you are more than welcome to check out the printer in person. My email is joeybernal at outlook dot com. <-- Don't want my email blasted by netbots lol. Please email me with any questions you have you will get a faster response than the forums.

Thanks,
Joey

As a possible complement to this kit I have an extra set of top and bottom plates for a rostock mini, Laser Cut from 8mm thick PMMA (plexi).

Drop me a message if interested, I want to see someone use this instead of it accumulating dust in my drawers so I'll do it at cost price (plus shipping from France).

---

Most of my technical comments should be correct, but is THIS one ?
Anyway, as a rule of thumb, always double check what people write.

I might even consider purchasing them to have a better chance at selling this build if the price is right. All tho shipping from France it might be costly. Can you email me with total price shipped to Modesto, CA 95350 USA. Email joeybernal at outlook dot com. Thanks.

Message sent.

There's a picture of similar plates - cut at the same time - here : [forums.reprap.org]

---

Most of my technical comments should be correct, but is THIS one ?
Anyway, as a rule of thumb, always double check what people write.

So I printed out a gregs extruder for the printer and also assembled the J-Head into the effector. Also attached the endstops but left unsoldered incase buyer wanted to use connectors instead. Extruder comes with all hardware in the picture. So all that's left in the plexi glass top and bottom pieces.

Price lowered.

$500 USD local pickup or $500 USD + Shipping.