Mini Height Sensor crashes into bed during homing January 27, 2017 11:37PM |
Registered: 8 years ago Posts: 34 |
; Ormerod 1 config file for dc42 Duet firmware M111 S0 ; Debug off M550 PQ ; Machine name (can be anything you like) M551 XXXXXXXX ; Machine password (currently not used) M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address ;*** Adjust the IP address and gateway in the following 2 lines to suit your network M552 PXXXXXXX ; IP address (0 = use DHCP) M554 PXXXXXXX; Gateway M553 PXXXXXXXX ; Netmask M555 P2 ; Set output to look like Marlin M575 P1 B57600 S1 ; Comms parameters for PanelDue G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M574 X1 Y1 Z0 S1; ; set endstop configuration (Y endstop only, at high end, active high) M906 X800 Y800 Z2000 E800 ; Set motor currents (mA) M563 P0 D0 H1 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures M92 X79.023194 Y79.207920 Z400.00 E417.00 ; Set extruder steps per mm (single nozzle) and steps for all axis ;*** If you have a dual-nozzle build, remove or comment out the previous line, and un-comment the following 3 lines ;M563 P1 D1 H2 ; Define tool 1 ;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures ;M92 E420:420 ; Set extruder steps/mm (dual nozzle) ;*** If you have a modulated IR probe without on-board microcontroller, change P1 to P2 in the following M558 P1 X0 Z1 ; Use an unmodulated Z probe or an intelligent Z probe G31 Z2.52 P500 ; Set the probe height and threshold (put your own values here) ;*** If you have a Duet board with 4.7K thermistor series resistors, change R1000 to R4700 to the following M305 commands M305 P0 T100000 R4700 H0 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction M305 P1 T100000 B4388 R4700 H0 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction ;M305 P2 R4700 H0 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction ;*** Adjust the XY coordinates in the following M557 commands to suit your build and the position of the IR sensor ;M557 P0 X60 Y0 ; Four... ;M557 P1 X60 Y165 ; ...probe points... ;M557 P2 X222 Y165 ; ...for bed... ;M557 P3 X222 Y0 ; ...levelling ;M557 P4 X141 Y82.5 ; 5th probe point for levelling (un-comment this if you are using a dc42 differential IR probe) ;*** if you are using axis compensation, put the figures in the following command M556 S78 X0 Y0 Z0 ; Axis compensation here M201 X200 Y200 Z3 E1000 ; Accelerations (mm/s^2) M203 X7500 Y7500 Z50 E3600 ; Maximum speeds (mm/min) M566 X600 Y600 Z30 E20 ; Minimum speeds mm/minute M208 X210 Y260 Z190 ; set axis maxima (adjust to suit your machine) M208 X0 Y0 Z0 S1 ; set axis minimum (adjust to make X=0 the edge of the bed) M569 P0 S1 M569 P1 S1 M569 P2 S1 M569 P3 S0 ; T0 ; select first hot end
G91 G1 Z4 F50 G1 Y120 F1000 G1 X110 F1000 G1 Z-180 F50 P1 G1 Z4 F50 G1 Z-4 F50 P1 G1 Y0 F1000 S1 G1X0 F1000 S1 G90
Re: Mini Height Sensor crashes into bed during homing January 28, 2017 04:54AM |
Registered: 10 years ago Posts: 14,672 |