Z axis homing issues and extruder problems February 18, 2016 04:29AM |
Registered: 8 years ago Posts: 8 |
; Huxley Duo config file for dc42 Duet firmware ; Based on RepRapPro version 1.04 M111 S0 ; Debug off M550 PMyHuxleyDuo ; Machine name (can be anything you like) M551 Preprap ; Machine password (used for FTP access) M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x14 ; MAC Address M552 P0.0.0.0 ; IP address (0 = use DHCP) M553 P255.255.255.0 ; Netmask M554 P192.168.1.1 ; Gateway M555 P2 ; Set output to look like Marlin G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M575 P1 B115200 S1 ; Set auxiliary serial port baud rate and require checksum (for PanelDue) M574 X1 Y1 Z1 S1 ; set endstop configuration (Y endstop only, at low end, active high) M569 P0 S1 ; Reverse the X motor M569 P3 S0 ; Don't reverse the extruder motor M906 X800 Y800 Z800 E800 I0.1 ; Set motor currents (mA) ; NO THERMISTORS SO NOT NEEDED ;M305 P0 T100000 R4700 ; bed thermistor is 100K with 4K7 series resistor ;M305 P1 R4700 ; first nozzle thermistor has 4K7 series resistor ;M305 P2 R4700 ; second nozzle thermistor has 4K7 series resistor M92 E660 ; Set extruder steps per mm M92 X92 Y80 Z1025 E420 ; XYZ E calibration M558 P0 ; Use a modulated Z probe (change to P1 if you have a dc42 diff IR zprobe) ;G31 Z0.6 P550 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup) M556 S78 X0 Y0 Z0 ; Put your axis compensation here M201 X3000 Y3000 Z150 E500 ; Accelerations (mm/s^2) M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min) M566 X200 Y200 Z30 E20 ; Maximum jerk rates mm/minute M563 P0 D0 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures M563 P1 D1 ; Define tool 1 Uncomment if you have a dual colour upgrade G10 P1 X19 S0 R0 ; Set tool 1 operating and standby temperatures Uncomment if you have a dual colour upgrade M208 X280 Y274 Z200 ; set axis maxima (adjust to suit your machine) M208 X0 Y0 Z0 S1 ; set axis minim (adjust to make X=0 and Y=0 the edge of the bed after homing) T0 ; select first hot end T1
; Ormerod 2 homeall file for use with dc42 Duet firmware ; Adjust the bed upper and lower limits in config.g (M208 commands) to get the correct homing positions G91 G1 Z4 F300 S1 G1 X-240 Y-240 F3000 S1 G1 X4 Y4 F600 G1 X-10 Y-10 Z-10 S1 G90 ; Adjust the XY coordinates in the following to place the IR sensor over a suitable spot ; If you are using a dc42 IR sensor then you can change the coordinates to be near the centre of the bed ;G1 X45 Y5 F2000 G30 ; This file leaves the head at the zprobe trigger height so that you can slip a piece of paper under it and then do G0 Z0 to check the height. ; If you prefer to send the printer to X0Y0Z0, un-comment the following lines G1 X0 Y0 F5000 G1 Z0 F300
Re: Z axis homing issues and extruder problems February 18, 2016 06:36AM |
Registered: 10 years ago Posts: 14,672 |