Marlin 1.1.4 : Message Endstops hit missing on G30

Very good days,

I have a prusa I3 rework 1.5 and decided to upgrade the firmware from 1.0.2 to 1.1.4.
Everything seems to work fine except that when I'm going a G30 I'm not getting the message "echo:endstops hit: Z:x.xx"

Givin a M119 gives me the correct answers :

SENT: M119
READ: Reporting endstop status
READ: x_min: open
READ: y_min: open
READ: z_min: TRIGGERED
READ: ok

But G30 :

SENT: G30
READ: echo:busy: processing
busy: processing
READ: echo:busy: processing
busy: processing
READ: echo:busy: processing
busy: processing
READ: echo:busy: processing
busy: processing
READ: echo:busy: processing
busy: processing
READ: echo:busy: processing
busy: processing
READ: Bed X: 0.00 Y: 18.00 Z: -1.91
READ: X:0.00 Y:0.00 Z:11.89 E:0.00 Count X:0 Y:0 Z:19024
READ: ok

Here M503:

SENT: M503
READ: echo:  G21    ; Units in mm
G21    ; Units in mm
READ: echo:  M149 C ; Units in Celsius
M149 C ; Units in Celsius
READ: 
READ: echo:Filament settings: Disabled
Filament settings: Disabled
READ: echo:  M200 D1.75
M200 D1.75
READ: echo:  M200 D0
M200 D0
READ: echoteps per unit:
Steps per unit:
READ: echo:  M92 X80.00 Y80.00 Z1600.00 E180.00
M92 X80.00 Y80.00 Z1600.00 E180.00
READ: echo:Maximum feedrates (units/s):
Maximum feedrates (units/s):
READ: echo:  M203 X200.00 Y200.00 Z5.00 E35.00
M203 X200.00 Y200.00 Z5.00 E35.00
READ: echo:Maximum Acceleration (units/s2):
Maximum Acceleration (units/s2):
READ: echo:  M201 X2000 Y2000 Z100 E2000
M201 X2000 Y2000 Z100 E2000
READ: echo:Acceleration (units/s2): P R T
Acceleration (units/s2): P R T
READ: echo:  M204 P2000.00 R2000.00 T2000.00
M204 P2000.00 R2000.00 T2000.00
READ: echo:Advanced: S T B X Z E
Advanced: S T B X Z E
READ: echo:  M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.40 E5.00
M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.40 E5.00
READ: echo:Home offset:
Home offset:
READ: echo:  M206 X0.00 Y0.00 Z0.00
M206 X0.00 Y0.00 Z0.00
READ: echo:Auto Bed Leveling:
Auto Bed Leveling:
READ: echo:  M420 S0
M420 S0
READ: echo:Material heatup parameters:
Material heatup parameters:
READ: echo:  M145 S0 H180 B70 F0
M145 S0 H180 B70 F0
READ:   M145 S1 H240 B110 F0
READ: echoID settings:
PID settings:
READ: echo:  M301 P22.20 I1.08 D114.00
M301 P22.20 I1.08 D114.00
READ: echo:Z-Probe Offset (mm):
Z-Probe Offset (mm):
READ: echo:  M851 Z-1.89
M851 Z-1.89
READ: ok

I also tried firmware 1.1.3, had the same issue.
On 1.0.2 it's working fine.
I getting crazy since 2 days, so if someone had a good idea how to troubleshoot !

Thanks and kind regards,
Nicolas.