Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 11:39AM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 11:45AM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 12:05PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 12:50PM |
Registered: 11 years ago Posts: 5,780 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 01:47PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 01:49PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:31PM |
Registered: 9 years ago Posts: 569 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:39PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:43PM |
Registered: 9 years ago Posts: 569 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:47PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:50PM |
Registered: 9 years ago Posts: 569 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 02:52PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 20, 2015 03:46PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 21, 2015 08:15PM |
Registered: 9 years ago Posts: 569 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 22, 2015 07:08AM |
Registered: 10 years ago Posts: 341 |
// The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD 33 #define MOTHERBOARD BOARD_ULTIMAKER #endif
#ifndef MOTHERBOARD #define MOTHERBOARD 33 #endif
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 22, 2015 04:31PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 22, 2015 04:39PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 22, 2015 05:46PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 22, 2015 07:38PM |
Registered: 10 years ago Posts: 341 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 09:03AM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 09:44AM |
Registered: 9 years ago Posts: 569 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 10:24AM |
Registered: 9 years ago Posts: 1,159 |
Quote
Kurzaa
Grats on your progress.
As for the fan, if you have it plugged into D9 (?), the fan is likely controlled by your slicer / firmware and should turn on after the first layer or two if set by your slicer settings. You should also be able to turn it on manually with ponterface, though your slicer settings might turn it back off temporarily when you start the print.
If you have an all metal hotend though, with the fan blowing directly on the fins of the hotend, you will want to play with your firmware to make sure it is turned on whenever the hotend is on. Still trying to figure that one out myself.
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 12:03PM |
Registered: 9 years ago Posts: 22 |
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 12:15PM |
Registered: 9 years ago Posts: 1,159 |
Quote
Dibbler
Quote
dougal1957
Actually safest way is to connect the Hotend fan directly to the 12v input on the board/PSU Output.
Doug
I did wonder about that Doug, But I was worried about dirtying the feed with noise from the motor.
Re: Please help with Sintron Prusa i3... stuck at the commissioning stage. March 23, 2015 12:21PM |
Registered: 9 years ago Posts: 22 |