Ormerod 2 error

Hi,

I got an error in the log file pronterface.exe.log, can anyone please tell me what this mean? thanks.
Traceback (most recent call last):
File "pronterface.py", line 1137, in recvcb
IndexError: list index out of range

The error of the machine is that the heated bed is not heating, and whenever I try to change the temperature of the hot ends using Proterface, the Proterface blocks and stopped responding.

I checked using Arduino serial monitor and the SD card was read at start up.

response for M105 command:

ok T: B:23.6 H0:23.6/-273.1 H1:68.2/200.0 H2:109.2/190.0


The configuration file is:
; Configuration file for RepRap Ormerod 2

; RepRapPro Ltd
;

; Copy this file to config.g if you have an Ormerod 2

; If you are updating a config.g that you already have you

; may wish to go through it and this file checking what you

; want to keep from your old file.

;
; For G-code definitions, see [reprap.org]

;
M111 S0 ; Debug off

M550 PMy RepRapPro Ormerod 2 ; Machine name (can be anything you like). With DHCP enabled connect to (example) [reprapproormerod2] (machine name with no spaces).

M551 Preprap ; Machine password (currently not used)

M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address

;M552 P0.0.0.0 ; Un-comment for DHCP

M552 P192.168.1.14 ; IP address, comment for DHCP

M553 P255.255.255.0 ; Netmask

M554 P192.168.1.1 ; Gateway, comment for DHCP

M555 P2 ; Set output to look like Marlin

G21 ; Work in millimetres

G90 ; Send absolute corrdinates...

M83 ; ...but relative extruder moves

M906 X800 Y1000 Z800 E800 ; Set motor currents (mA)

M305 P0 R4700 ; Set the heated bed thermistor series resistor to ;4K7

M305 P1 X100 ; ***Set hot end 1 thermocouple to input channel 100
M305 P2 X101 ; ***Set hot end 2 thermocouple to input channel 101
M569 P0 S0 ; Set X axis direction

M92 E420 ; Set extruder steps per mm

M558 P2 ; Use a modulated Z probe
G31 Z0.8 P600 ;***Sets Z probe homing information to detect 1.8mm above bed where probe reads 604.

M556 S75 X0 Y0 Z0 ; Put your axis compensation here

M201 X500 Y500 Z15 E500 ; Accelerations (mm/s^2)

M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)

M566 X200 Y200 Z30 E20 ; Minimum speeds mm/minute

M563 P0 D0 H1 ; Define tool 0

G10 P0 S110 R200 ; Set tool 0 operating and standby temperatures

M563 P1 D1 H2 ; Define tool 1, uncomment if you have a dual colour upgrade

G10 P1 X30 S110 R190 ; Set tool 1 operating and standby temperatures, uncomment if you have a dual colour upgrade
M143 S370 ; *** Sets Maximum Temperature

M570 S800 ; *** After a heater has been switched on, wait 350 seconds to heat or flag fault.

Edited 1 time(s). Last edit at 09/21/2016 06:17AM by junhw.

Quote
junhw
Hi,

I got an error in the log file pronterface.exe.log, can anyone please tell me what this mean? thanks.
Traceback (most recent call last):
File "pronterface.py", line 1137, in recvcb
IndexError: list index out of range

The error shown is related to a python file (*.py) within pronterface. The fact you get a temperature result from the M105 command show there is no problem with the printer.
an index out of range error can be caused by asking for a number in location not available
In python an index can be used to store values or data, so say I have an index called numbers(1..10) and I ask for 11 that would be out of range of my index.

Maybe update pronterface or use the web control interface as pronterface is a bit old

---

Supporting 3D Printers with Parts and Build services.
Printer: Ormerod 2 (528.4) Duel extruder set-up with Aluminium X-Rib, RRPro Firmware v1.11-ch (2016-04-08)

Thanks for the reply, indeed it is the py file, I had two extruder installed, maybe the corresponding change in the py file is not correct. Will check that.

Cheers.