[SOLVED] X & Y don't work ONLY during printing October 10, 2015 01:14AM |
Registered: 8 years ago Posts: 5 |
Re: X & Y don't work ONLY during printing October 10, 2015 03:14AM |
Registered: 8 years ago Posts: 5,232 |
Re: X & Y don't work ONLY during printing October 10, 2015 11:55AM |
Registered: 8 years ago Posts: 5 |
Quote
o_lampe
Are your endstops mounted as min or max? Where is 0,0,0 on your bed?
Are your endstops configured in firmware as min or max?
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 #define X_ENABLE_ON 0 #define Y_ENABLE_ON 0 #define Z_ENABLE_ON 0 #define E_ENABLE_ON 0 // For all extruders // Disables axis when it's not being used. #define DISABLE_X false #define DISABLE_Y false #define DISABLE_Z false #define DISABLE_E false // For all extruders #define INVERT_X_DIR false // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true #define INVERT_E0_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR 1 #define Y_HOME_DIR 1 #define Z_HOME_DIR -1 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // Travel limits after homing #define X_MAX_POS 0 #define X_MIN_POS -170 #define Y_MAX_POS 0 #define Y_MIN_POS -170 #define Z_MAX_POS 180 #define Z_MIN_POS 0 ... // The position of the homing switches //#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) //Manual homing switch locations: // For deltabots this means top and center of the Cartesian print volume. #define MANUAL_X_HOME_POS 0 #define MANUAL_Y_HOME_POS 0 #define MANUAL_Z_HOME_POS 0
// The position of the homing switches #define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) //Manual homing switch locations: // For deltabots this means top and center of the Cartesian print volume. #define MANUAL_X_HOME_POS 85 #define MANUAL_Y_HOME_POS 85 #define MANUAL_Z_HOME_POS 0
Re: X & Y don't work ONLY during printing October 10, 2015 12:06PM |
Registered: 8 years ago Posts: 80 |
Re: X & Y don't work ONLY during printing October 10, 2015 12:10PM |
Registered: 8 years ago Posts: 5 |
Re: X & Y don't work ONLY during printing October 10, 2015 12:25PM |
Registered: 8 years ago Posts: 80 |
Re: X & Y don't work ONLY during printing October 10, 2015 12:30PM |
Registered: 8 years ago Posts: 5 |
#define min_software_endstops false // If true, axis won't move to coordinates less than HOME_POS. #define max_software_endstops false // If true, axis won't move to coordinates greater than the defined lengths below.
Re: X & Y don't work ONLY during printing October 10, 2015 01:24PM |
Registered: 8 years ago Posts: 5 |
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false #define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true #define INVERT_E0_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR -1 #define Y_HOME_DIR -1 #define Z_HOME_DIR -1 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // Travel limits after homing #define X_MAX_POS 170 #define X_MIN_POS 0 #define Y_MAX_POS 170 #define Y_MIN_POS 0 #define Z_MAX_POS 180 #define Z_MIN_POS 0
Re: X & Y don't work ONLY during printing October 10, 2015 06:46PM |
Registered: 8 years ago Posts: 430 |
Re: X & Y don't work ONLY during printing October 11, 2015 03:30AM |
Registered: 8 years ago Posts: 5,232 |