Geeetech Prusa Mendel I3 Temperature June 30, 2015 04:41PM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature June 30, 2015 06:06PM |
Registered: 8 years ago Posts: 183 |
Re: Geeetech Prusa Mendel I3 Temperature July 01, 2015 01:13AM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 01, 2015 12:02PM |
Registered: 8 years ago Posts: 183 |
Re: Geeetech Prusa Mendel I3 Temperature July 02, 2015 04:23AM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 02, 2015 12:36PM |
Registered: 9 years ago Posts: 606 |
Quote
CWLouw
Hi Montiey,
Yes the board was pre-loaded with some Geeetech software, but I broke it. Last night I tried to look at it and instead of opening a sketch I uploaded a different board I was looking at. So now the LCD only shows 3 lines of blocks. Maybe it's actually a better place to be, now I can start from scratch. Were can I find a step by step instructions for dummies?
Re: Geeetech Prusa Mendel I3 Temperature July 02, 2015 12:59PM |
Registered: 8 years ago Posts: 183 |
Re: Geeetech Prusa Mendel I3 Temperature July 03, 2015 01:01AM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 03, 2015 01:23AM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 04, 2015 02:43AM |
Registered: 9 years ago Posts: 476 |
Re: Geeetech Prusa Mendel I3 Temperature July 06, 2015 04:21PM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 06, 2015 05:19PM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 06, 2015 07:10PM |
Registered: 8 years ago Posts: 183 |
Re: Geeetech Prusa Mendel I3 Temperature July 07, 2015 02:27AM |
Registered: 8 years ago Posts: 13 |
Quote
Montiey
What do you mean by the steppers going into idle? Do they actively become hard to impossible to turn?
Also, what controller board does your i3 have? It didn't say anything on their website, or at least not anything that I could find.
Re: Geeetech Prusa Mendel I3 Temperature July 07, 2015 12:52PM |
Registered: 8 years ago Posts: 183 |
Re: Geeetech Prusa Mendel I3 Temperature July 07, 2015 02:19PM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 07, 2015 06:38PM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 07, 2015 09:05PM |
Registered: 8 years ago Posts: 183 |
#define WELCOME_MSG MACHINE_NAME "whatever was here"to anything you want in your language.h file. I was pretty confused with the firmware files in the beginning, so just wanted to point out that you should put your whole firmware folder (mine was named Marlin_RAMPS_EPCOS_i38) in your arduino sketches folder, and then from the IDE you can easily just open it from the open menu (a million tabs will pop up, but there should be a down arrow in the righthand side of the bar somewhere that will give you a scrollable list).
Re: Geeetech Prusa Mendel I3 Temperature July 08, 2015 06:53AM |
Registered: 8 years ago Posts: 13 |
Re: Geeetech Prusa Mendel I3 Temperature July 08, 2015 11:00AM |
Registered: 8 years ago Posts: 183 |