Welcome! Log In Create A New Profile

Advanced

SLS from fiber laser engraver

Posted by trgtylcnky 
SLS from fiber laser engraver
February 10, 2017 05:05AM
Hi,
I came across this machine: [www.lightobject.com]
It has 110 x 110 mm working area and 0.01 mm resolution. I am thinking about building SLS machine based on this.

OpenSLS is based on a CO2 laser cutter. I think this fiber laser engraver would be better on many things; cooling, speed, footprint etc...
VDX
Re: SLS from fiber laser engraver
February 10, 2017 06:29AM
... good luck smileys with beer


Viktor
Re: SLS from fiber laser engraver
February 10, 2017 08:32AM
So which ship from China
is delivering the 5 tons of powdered nylon / abs / pla
to be used for your sintering

Could you scoop me up 20 pounds that I can try sintering?

confused smiley
VDX
Re: SLS from fiber laser engraver
February 10, 2017 12:42PM
... it's only "coincidence", but today I too got a XY-galvoscanner with 110x110mm scanning area, driven with E1701D scanner controller and software BeamConstruct running winking smiley

Now I have to build adapters and holders for three types of fiber-laser heads and another holder for a beam-expander to start testing with fiber-coupled laserdiodes too ...


Viktor
Re: SLS from fiber laser engraver
July 19, 2017 04:54AM
Hello Viktor,

I am trying to make a SLS printer using E1701D controller and Beamconstruct. But the topic is new for me and I do not have enough knowledge.

I see that you have experience with this board. I have just started and I do not know how to connect my laser to the controller even that I have the manual.
My laser driver has two controlling pins. One of them will be connected to LaserA pin of the controller. Should I connect the other one to the Pin 12 as GND.Or not?
I know it`s a very simple question but since the laser control signal of Controller have two GND pins (12,14), I am confused.

Thank you very much in advanced.
Sara
Attachments:
open | download - dd.png (70.9 KB)
VDX
Re: SLS from fiber laser engraver
July 19, 2017 12:10PM
Hi Sara,

the GND's are internally connected, so you can use any of them.

My laser needs two driving connections from "LaserA" and "Gate" (both with GND) to control the Power and MO -- but this depends on your laser type, so can vary ...


Viktor
Re: SLS from fiber laser engraver
July 19, 2017 05:05PM
I'll ask again

Where are you getting powdered nylon / abs / pla
to be used for your sintering

confused smiley
VDX
Re: SLS from fiber laser engraver
July 19, 2017 11:49PM
... you can search for "PA12" for nylon powder -- e.g. [www.vestosint.de]

White powder can be mixed with carbon black to get better absorbing, when using diode lasers ...


Viktor
Re: SLS from fiber laser engraver
July 20, 2017 12:46AM
Thank you very much Viktor.

I am using this Diode Laser.
[www.lasertack.com]

I realise that I have to switch to the E1701A controller, because my Galvo Scanner inputs are analog. Digital controller was not a good idea. I am waiting for the new controller to start to work again. smiling smiley
Re: SLS from fiber laser engraver
July 20, 2017 07:04PM
So will they sell you less than a metric ton?

1 kg nylon powder 139 euro?

confused smiley
VDX
Re: SLS from fiber laser engraver
July 20, 2017 11:14PM
... common selling amounts are 25kg -- but mostly b2b only, "not for privatiers" eye rolling smiley

But with some luck you can get free samples for testing - got some meters to kilometers thin wire or up to 2kg lignin powder for free, when chatted with material developers winking smiley


Viktor
Sorry, only registered users may post in this forum.

Click here to login