Welcome! Log In Create A New Profile

Advanced

General Mendel Topics

Prusa i2, Prusa i1, Prism, Sells, and other Mendel variants 
Page 1 of 66    Pages: 12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

RepRap Samuel - A variation on the Mendel   (Pages: 1 2 3 4)

by silpstream 		26,623 119 04/22/2024 05:19AM
Last Post by Jase

RepRapPro Mendel commissioning(2012) Attachments

by trusty-trev 		556 1 01/15/2024 10:52AM
Last Post by trusty-trev

leveling problem the nozzle hitting bed Creality CR-R5 pro Attachments

by Four_Nobody 		2,679 1 12/01/2022 05:57PM
Last Post by Four_Nobody

BL touch on a Mendel carriage.

by zBeeble 		2,437 1 08/03/2022 04:28PM
Last Post by zBeeble

I need your help about the board MK808B Clone eye popping smiley Attachments

by ADRIANO3D 		9,907 15 01/14/2022 11:05PM
Last Post by Dust

Melzi Ardentissimo mendel i2

by yaboo 		2,702 1 12/20/2021 07:43PM
Last Post by yaboo

Prusa Mendel Z axis doesnt work

by B3nki 		5,512 3 08/25/2021 01:58PM
Last Post by shady0248

MK3 Alu-Heatbed how to print with a hole in center.

by Carlos Fellip 		5,693 6 06/25/2021 01:16PM
Last Post by ag123

RepRapPro Mendel 3 - printable parts

by nanotone 		3,892 2 06/06/2021 03:14PM
Last Post by Gaou

RepRap iTopie - A Prusa i3 evolution - Development discussion   (Pages: 1 2)

by skarab 		23,231 43 02/20/2021 04:15PM
Last Post by NovaHuta

Prusa i3 mandel

by yar60 		4,068 2 02/12/2021 05:05AM
Last Post by Dust

New heat bed for Orcabot 0.4 Attachments

by NozzleMover 		4,279 1 12/07/2020 08:24AM
Last Post by NozzleMover

Kapton forming bubbles under print

by mlaustin66 		6,338 11 09/28/2020 05:17PM
Last Post by Keveeeeeee

Strange loud buzz before homing normally Attachments

by villainousindustries 		5,485 8 06/02/2020 01:34PM
Last Post by Justinjjhcs1

Buzzing steppers when homing

by cmerce 		6,941 7 06/02/2020 04:06AM
Last Post by MKSA

Gen 6 delux electronics - Programm with ISP

by NozzleMover 		4,861 2 05/27/2020 03:36AM
Last Post by NozzleMover

Attempting to print above bed. Attachments

by TerryD15 		5,153 1 03/12/2020 04:32AM
Last Post by TerryD15

My printer is set up with the nozzle offsets and when the printer homes the nozzle is just right. The Attachments

by TerryD15 		4,960 3 03/12/2020 02:11AM
Last Post by TerryD15

Z axis not lowering Attachments

by TerryD15 		5,169 2 03/10/2020 11:24AM
Last Post by TerryD15

Prusa i3 Isee Board, Needs Firmware urgent! please smiling smiley Attachments

by edisonpaul4 		8,185 6 12/18/2019 05:32PM
Last Post by poggia10

Here is my Prusa i3 !   (Pages: 1 2)

by franck 		23,547 43 10/26/2019 05:51AM
Last Post by Ohmarinus

How to recycle a ReprRapPro MENDEL

by Jef_Lord 		6,555 6 08/01/2019 08:49AM
Last Post by Jef_Lord

Project log: Air 2 upgrade

by Ohmarinus 		6,577 4 04/03/2019 03:02PM
Last Post by Ohmarinus

Strange lumpiness after print is about 1cm high Attachments

by davies46 		5,876 4 03/24/2019 06:19AM
Last Post by MotoBarsteward

Advice on Firmware/Software and Extruder

by Adam.m.Nelson 		6,082 4 03/18/2019 03:15PM
Last Post by dlc60

printrbot printrboard Rev. D

by ola 		6,066 2 01/21/2019 09:50AM
Last Post by Dust

my prusa i2 is stalling on the Z changed stepper driver and greased screws

by terramir 		6,363 6 11/27/2018 09:44AM
Last Post by Roberts_Clif

Dimension error in Z

by ChicoCyberGoth 		6,130 12 10/31/2018 11:39AM
Last Post by blt3dp

Problem with X carriage and extruder Attachments

by ChicoCyberGoth 		6,015 1 10/27/2018 10:18PM
Last Post by ChicoCyberGoth

Anet A8 Homing Issues

by punker970 		5,855 2 10/27/2018 02:26AM
Last Post by jefbed
Page 1 of 66    Pages: 12345NextLast