Re: New RepRapFirmware 1.09r-dc42 January 26, 2016 01:44PM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 January 26, 2016 05:02PM |
Registered: 9 years ago Posts: 51 |
Quote
dc42
Some suggestions:
1. Make sure you are running DuetWebControl 1.08. It avoids an issue caused by over-long cookies that affected some systems, depending on what browser you used.
Already on it and loving the ability to edit the config file!
2. Clear all cookies used by the Duet's IP address from your browser(s).
Gave it a go with no change
3. Check that the same IP address isn't allocated to another device. If in doubt, allocate a static IP address to the Duet, outside the range that your router auto-allocates from.
I think this was my issue with dropouts/unable to connect. Tried on anther router first so the was just the kossel and laptop, all worked (but slow, see below). Went back to my home network and forced the router to reasign the printer a new IP and can now connect. Will change to static IP (need to do some house keeping for all my connected devices it looks)
4. Does it work well for a while and then start to fail after the printer has been on for a while? If so, it could be a sign that the Duet is getting too hot, especially if it is mounted in a confined space.
The board isn't enclosed and not confined.
5. Try a different browser, to see if the problems occur using one browser and not another. I have found Chrome the most reliable. A recent version of FireFox that I tried was refusing to send file upload data for on apparent reason when uploading large files.
Yep, always use chrome.
6. Try a different SD card.
Now this was a known good SD card and was working fast, but i swapped it out (again) for a freshly formatted one and now those connection/download speeds are nice and quick again! I still feel like the cards are getting corrupted after a few shutdowns maybe?
7. Otherwise post a Wireshark trace, filtered by the IP address of the Duet, showing what happened before a disconnect.
Re: New RepRapFirmware 1.09r-dc42 January 27, 2016 11:26AM |
Registered: 8 years ago Posts: 319 |
Quote
wayno complaino
Quote
mhackney
Routinely seeing > 200 kb/s
I saw significant speed increases on the first day of use, the web app opened and connected within seconds and uploading files didnt feel like a wait.
Now though im getting AJAX errors, dropouts, taking forever to load the web app and when it does work im seeing 11kb/s uploads. Pretty much as i was getting before when using k and previous. I have a feeling (because my knowledge is limited) this is more of a network problem than firmware or web app problem though. I dont get network problems with access to Pi's or webcams if i use the same connection though (physically unplugging the network cable from the duet and using on another network heavy device). Its unreliable enough for me to go back to manually using the SD Card to transfer files between the computer and Duet, really annoying.
Any help really appreciated!
Re: New RepRapFirmware 1.09r-dc42 February 03, 2016 11:23AM |
Registered: 8 years ago Posts: 31 |
IP 192.168.1.2.65205 > 192.168.1.42.http: tcp 393 0x0000: 4500 01b1 ef9b 4000 4006 c62e c0a8 0102 E.....@.@....... 0x0010: c0a8 012a feb5 0050 7b45 5168 00cc 92b5 ...*...P{EQh.... 0x0020: 5018 ffff 0ce3 0000 4745 5420 2f72 725f P.......GET./rr_ 0x0030: 7374 6174 7573 3f74 7970 653d 3320 4854 status?type=3.HT 0x0040: 5450 2f31 2e31 0d0a 486f 7374 3a20 3139 TP/1.1..Host:.19 0x0050: 322e 3136 382e 312e 3432 0d0a 4163 6365 2.168.1.42..Acce 0x0060: 7074 2d4c 616e 6775 6167 653a 2065 6e2d pt-Language:.en- 0x0070: 7573 0d0a 4163 6365 7074 2d45 6e63 6f64 us..Accept-Encod 0x0080: 696e 673a 2067 7a69 702c 2064 6566 6c61 ing:.gzip,.defla 0x0090: 7465 0d0a 436f 6e6e 6563 7469 6f6e 3a20 te..Connection:. 0x00a0: 6b65 6570 2d61 6c69 7665 0d0a 4163 6365 keep-alive..Acce 0x00b0: 7074 3a20 6170 706c 6963 6174 696f 6e2f pt:.application/ 0x00c0: 6a73 6f6e 2c20 7465 7874 2f6a 6176 6173 json,.text/javas 0x00d0: 6372 6970 742c 202a 2f2a 3b20 713d 302e cript,.*/*;.q=0. 0x00e0: 3031 0d0a 5573 6572 2d41 6765 6e74 3a20 01..User-Agent:. 0x00f0: 4d6f 7a69 6c6c 612f 352e 3020 284d 6163 Mozilla/5.0.(Mac 0x0100: 696e 746f 7368 3b20 496e 7465 6c20 4d61 intosh;.Intel.Ma 0x0110: 6320 4f53 2058 2031 305f 395f 3529 2041 c.OS.X.10_9_5).A 0x0120: 7070 6c65 5765 624b 6974 2f36 3031 2e33 ppleWebKit/601.3 0x0130: 2e39 2028 4b48 544d 4c2c 206c 696b 6520 .9.(KHTML,.like. 0x0140: 4765 636b 6f29 2056 6572 7369 6f6e 2f39 Gecko).Version/9 0x0150: 2e30 2e32 2053 6166 6172 692f 3533 372e .0.2.Safari/537. 0x0160: 3836 2e33 0d0a 5265 6665 7265 723a 2068 86.3..Referer:.h 0x0170: 7474 703a 2f2f 3139 322e 3136 382e 312e ttp://192.168.1. 0x0180: 3432 2f0d 0a44 4e54 3a20 310d 0a58 2d52 42/..DNT:.1..X-R 0x0190: 6571 7565 7374 6564 2d57 6974 683a 2058 equested-With:.X 0x01a0: 4d4c 4874 7470 5265 7175 6573 740d 0a0d MLHttpRequest... 0x01b0: 0a . IP 192.168.1.42.http > 192.168.1.2.65205: tcp 47 0x0000: 4500 0057 71b5 0000 ff06 c66e c0a8 012a E..Wq......n...* 0x0010: c0a8 0102 0050 feb5 00cc 92b5 7b45 52f1 .....P......{ER. 0x0020: 5018 09df 2113 0000 4854 5450 2f31 2e31 P...!...HTTP/1.1 0x0030: 2035 3030 204e 6f74 2061 7574 686f 7269 .500.Not.authori 0x0040: 7a65 640a 436f 6e6e 6563 7469 6f6e 3a20 zed.Connection:. 0x0050: 636c 6f73 650a 0a close..
Re: New RepRapFirmware 1.09r-dc42 February 03, 2016 02:34PM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 04, 2016 07:00AM |
Registered: 8 years ago Posts: 31 |
Re: New RepRapFirmware 1.09r-dc42 February 10, 2016 12:21PM |
Registered: 13 years ago Posts: 268 |
Re: New RepRapFirmware 1.09r-dc42 February 12, 2016 03:03AM |
Registered: 10 years ago Posts: 14,672 |
Quote
Koko76
I have had a lot of issues with file uploads, using 1.09r and web 1.08. Still trying to localize when and why it happens, as it may not be duet related but I figured I give the data I have. Using a Mac laptop and either Chrome, Firefox or Safari I get frequent (more often than not) super slow or stopping file transfers or a file that makes it to 100% and hangs without completion. With Firefox/Chrome and Ubuntu on a different box I get less issues, but still have similar problems. The duet is connected to a wireless extender for network access which appears to work fine for the most part. I have no problems with the web interface staying active through a print or beyond.
Re: New RepRapFirmware 1.09r-dc42 February 12, 2016 07:49AM |
Registered: 13 years ago Posts: 268 |
Re: New RepRapFirmware 1.09r-dc42 February 19, 2016 07:52AM |
Registered: 8 years ago Posts: 31 |
Re: New RepRapFirmware 1.09r-dc42 February 19, 2016 12:46PM |
Registered: 10 years ago Posts: 665 |
Re: New RepRapFirmware 1.09r-dc42 February 19, 2016 04:27PM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 19, 2016 07:43PM |
Registered: 13 years ago Posts: 268 |
Re: New RepRapFirmware 1.09r-dc42 February 20, 2016 06:07AM |
Registered: 10 years ago Posts: 466 |
Re: New RepRapFirmware 1.09r-dc42 February 21, 2016 03:22AM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 21, 2016 02:49PM |
Registered: 10 years ago Posts: 466 |
Quote
dc42
I suggest you look at the differences between the config.g in my sys-Ormerod1 folder and your own config.g file, then work out what changes to make to yours. The main one is the M574 command to tell the firmware that the Y endstop is at the high end.
Re: New RepRapFirmware 1.09r-dc42 February 21, 2016 05:38PM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 21, 2016 06:01PM |
Registered: 10 years ago Posts: 466 |
Quote
dc42
2. Yes. RRP changed back to the convention of tools being numbered T0, T1 etc. for better compatibility with slicing programs and other firmware. Use T-1 to deselect all tools. But you may still need to include T0 in your Cura start gcode.
3. The firmware default position for the homing switches is at the low end of each axis, as it is on Ormerod 2. For Ormerod 1, you need at least M574 Y2 to tell it that the Y homing switch is at the high end of the axis.
Re: New RepRapFirmware 1.09r-dc42 February 22, 2016 02:11AM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 22, 2016 05:22AM |
Registered: 10 years ago Posts: 466 |
Re: New RepRapFirmware 1.09r-dc42 February 22, 2016 12:21PM |
Registered: 10 years ago Posts: 466 |
Quote
DC42
With the power off, you should reverse the X motor connector so that the wire colours are in the same order as the other motors. Or you can edit the M569 command for the X motor. Otherwise it will run backwards.
Re: New RepRapFirmware 1.09r-dc42 February 22, 2016 03:17PM |
Registered: 10 years ago Posts: 14,672 |
Re: New RepRapFirmware 1.09r-dc42 February 28, 2016 11:17AM |
Registered: 9 years ago Posts: 28 |
Re: New RepRapFirmware 1.09r-dc42 February 29, 2016 03:32AM |
Registered: 10 years ago Posts: 14,672 |