Firmware Line Issue
Posted by dmoore0210
|
Firmware Line Issue February 14, 2015 11:15PM |
I've been getting this issue and I'm not sure where the problem lies as I've changed a few things around..
22:54:48.709 : No start signal detected - forcing start
22:54:56.470 : No start signal detected - forcing start
22:55:34.967 : start
22:55:34.967 : echo:Marlin 1.0.0
22:55:34.971 : echo: Last Updated: Feb 14 20158-15-1322:55:13 | Author: (FOLGER TECH, 8 i3 Prusa Config)
22:55:34.971 : Compiled: Feb 14 2015
22:55:34.971 : echo: Free Memory: 5516 PlannerBufferBytes: 1232
22:55:35.233 : Error:0
22:55:35.237 : : Extruder switched off. MINTEMP triggered !
22:55:35.242 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:35.414 : echo:Unknown command: ""
22:55:36.090 : FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:[www.mendel-parts.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:FolgerTech EXTRUDER_COUNT:1
22:55:36.097 : echo:Active Extruder: 0
22:55:36.105 : echo:Active Extruder: 0
22:55:40.624 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.665 : Resend: 1
22:55:44.679 : FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:[www.mendel-parts.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:FolgerTech EXTRUDER_COUNT:1
22:55:44.684 : echo:Active Extruder: 0
22:55:44.684 : Error:0
22:55:44.687 : : Extruder switched off. MINTEMP triggered !
22:55:44.691 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.695 : Error:No Checksum with line number, Last Line: 7
22:55:44.695 : Resend: 8
22:55:44.698 : Error:Line Number is not Last Line Number+1, Last Line: 7
22:55:44.698 : Resend: 8
22:55:44.703 : echo:Active Extruder: 0
22:55:44.707 : Error:Line Number is not Last Line Number+1, Last Line: 11
22:55:44.711 : Resend: 12
22:55:44.714 : Error:No Line Number with checksum, Last Line: 11
22:55:44.715 : Error:Line Number is not Last Line Number+1, Last Line: 11
22:55:44.715 : Resend: 12
22:55:44.723 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.728 : Error:No Line Number with checksum, Last Line: 15
22:55:44.728 : Error:Line Number is not Last Line Number+1, Last Line: 15
22:55:44.728 : Resend: 16
22:55:44.735 : Resend: 7
22:55:44.739 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.744 : Resend: 7
22:55:44.748 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.748 : Resend: 7
22:55:44.757 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.757 : Resend: 10
22:55:44.760 : Error:No Line Number with checksum, Last Line: 9
22:55:44.761 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.761 : Resend: 10
22:55:44.765 : echo:Active Extruder: 0
22:55:44.769 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.769 : Resend: 14
22:55:44.773 : echo:Unknown command: "6"
22:55:44.773 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.773 : Resend: 14
22:55:44.781 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.781 : Resend: 14
22:55:44.786 : echo:endstops hit: Y:-0.01
22:55:44.786 : Resend: 7
22:55:44.790 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.790 : Resend: 7
22:55:44.794 : Error:No Line Number with checksum, Last Line: 6
22:55:44.794 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.794 : Resend: 7
22:55:44.798 : Error:No Line Number with checksum, Last Line: 6
22:55:44.798 : Error:checksum mismatch, Last Line: 6
22:55:44.801 : Resend: 7
22:55:44.810 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.810 : Resend: 10
22:55:44.813 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.813 : Resend: 10
22:55:44.818 : echo:Active Extruder: 0
22:55:44.822 : Error:0
22:55:44.822 : : Extruder switched off. MINTEMP triggered !
22:55:44.826 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.830 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.830 : Resend: 14
22:55:44.842 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.844 : Resend: 13
22:55:44.850 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.850 : Resend: 13
22:55:44.855 : echo:endstops hit: Y:-0.03
22:55:44.859 : Resend: 13
22:55:44.862 : Error:No Line Number with checksum, Last Line: 12
22:55:44.862 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.862 : Resend: 13
22:55:44.871 : echo:endstops hit: Y:-0.04
22:55:44.871 : Resend: 13
22:55:44.879 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.879 : Resend: 13
22:55:44.883 : Error:No Line Number with checksum, Last Line: 12
22:55:44.883 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.883 : Resend: 13
22:55:44.892 : echo:endstops hit: Y:-0.05
22:55:44.896 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.896 : Resend: 17
22:55:44.899 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.899 : Resend: 17
22:55:44.904 : Resend: 13
22:55:44.907 : Error:No Line Number with checksum, Last Line: 12
22:55:44.908 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.908 : Resend: 13
22:55:44.912 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.912 : Resend: 13
22:55:44.917 : Error:No Line Number with checksum, Last Line: 12
22:55:44.917 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.917 : Resend: 13
22:55:44.922 : Error:No Line Number with checksum, Last Line: 12
22:55:44.924 : echo:endstops hit: Y:-0.06
22:55:44.928 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.928 : Resend: 17
22:55:44.937 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.937 : Resend: 17
22:55:44.940 : Error:No Line Number with checksum, Last Line: 16
22:55:44.941 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.941 : Resend: 17
22:55:44.945 : Resend: 13
22:55:44.950 : Error:No Line Number with checksum, LasN17 M99 12
22:55:44.950 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.950 : Resend: 13
22:55:44.953 : Error:No Line Number with checksum, Last Line: 12
22:55:44.953 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.953 : Resend: 13
22:55:44.957 : Error:No Line Number with checksum, Last Line:Error:0
22:55:44.957 : : Extruder switched off. MINTEMP triggered !
22:55:44.961 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.965 : 12
22:55:44.965 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.965 : Resend: 13
22:55:44.978 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.982 : Resend: 13
22:55:44.986 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.986 : Resend: 13
22:55:44.995 : echo:endstops hit: Y:-0.08
22:55:44.995 : Resend: 13
22:55:44.998 : Error:No Line Number with checksum, Last Line: 12
22:55:45.002 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.002 : Resend: 13
22:55:45.005 : Error:No Line Number with checksum, Last Line: 12
22:55:45.006 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.006 : Resend: 13
22:55:45.014 : echo:endstops hit: Y:-0.09
22:55:45.018 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.019 : Resend: 17
22:55:45.022 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.022 : Resend: 17
22:55:45.027 : Resend: 13
22:55:45.030 : Error:No Line Number with checksum, Last Line: 12
22:55:45.031 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.031 : Resend: 13
22:55:45.036 : echo:Unknown command: "20"
22:55:45.036 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.036 : Resend: 13
22:55:45.039 : echo:Unknown command: "4"
22:55:45.039 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.039 : Resend: 13
22:55:45.043 : Error:No Line Number with checksum, Last Line: 12
22:55:45.043 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.047 : Resend: 13
22:55:45.050 : Error:No Line Number with checksum, Last Line: 12
22:55:45.051 : echo:endstops hit: Y:-0.10
22:55:45.056 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.056 : Resend: 17
22:55:45.059 : Error:No Line Number with checksum, Last Line: 16
22:55:45.063 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.063 : Resend: 17
22:55:45.066 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.066 : Resend: 17
22:55:45.071 : Resend: 13
22:55:45.075 : Error:No Line Number with checksum, Last Line: 12
22:55:45.075 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.075 : Resend: 13
22:55:45.084 : echo:endstops hit: Y:-0.11
22:55:45.088 : Resend: 13
22:55:45.093 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.093 : Resend: 13
22:55:45.096 : Error:0
22:55:45.097 : : Extruder switched off. MINTEMP triggered !
22:55:45.101 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.101 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.104 : Resend: 13
22:55:45.117 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.117 : Resend: 13
22:55:45.125 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.125 : Resend: 13
22:55:45.130 : echo:endstops hit: Y:-0.12
22:55:45.134 : Resend: 13
22:55:45.137 : Error:No Line Number with checksum, Last Line: 12
22:55:45.137 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.137 : Resend: 13
22:55:45.146 : echo:endstops hit: Y:-0.14
22:55:45.146 : Resend: 13
22:55:45.154 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.154 : Resend: 13
22:55:45.157 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.157 : Resend: 13
22:55:45.166 : echo:endstops hit: Y:-0.15
22:55:45.170 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.170 : Resend: 17
22:55:45.174 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.174 : Resend: 17
22:55:45.179 : Resend: 13
22:55:45.183 : Error:No Line Number with checksum, Last Line: 12
22:55:45.183 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.183 : Resend: 13
22:55:45.186 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.186 : Resend: 13
22:55:45.191 : echo:endstops hit: Y:-0.16
22:55:45.195 : Resend: 13
22:55:45.200 : echo:endstops hit: Y:-0.17
22:55:45.203 : Resend: 13
22:55:45.207 : echo:endstops hit: Y:-0.19
22:55:45.211 : Resend: 13
22:55:45.214 : Error:No Line Number with checksum, Last Line: 12
22:55:45.215 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.215 : Resend: 13
22:55:45.223 : echo:endstops hit: Y:-0.20
22:55:45.223 : Resend: 13
22:55:45.227 : echo:Unknown command: "20"
22:55:45.227 : Error:Line Number is not Last LError:0
22:55:45.232 : : Extruder switched off. MINTEMP triggered !
22:55:45.236 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.236 : ine Number+1, Last Line: 12
22:55:45.236 : Resend: 13
22:55:45.248 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.252 : Resend: 13
22:55:45.256 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.256 : Resend: 13
22:55:45.264 : echo:endstops hit: Y:-0.21
22:55:45.265 : Resend: 13
22:55:45.268 : echo:Unknown command: "20"
22:55:45.273 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.273 : Resend: 13
22:55:45.276 : Error:No Line Number with checksum, Last Line: 12
22:55:45.277 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.277 : Resend: 13
22:55:45.285 : echo:endstops hit: Y:-0.22
22:55:45.289 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.289 : Resend: 17
22:55:45.292 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.292 : Resend: 17
22:55:45.297 : Resend: 13
22:55:45.300 : Error:No Line Number with checksum, Last Line: 12
22:55:45.302 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.302 : Resend: 13
22:55:45.305 : echo:Unknown command: "20"
22:55:45.306 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.306 : Resend: 13
22:55:45.310 : Error:No Line Number with checksum, Last Line: 12
22:55:45.310 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.310 : Resend: 13
22:55:45.315 : Error:No Line Number with checksum, Last Line: 12
22:55:45.315 : Error:No Checksum with line number, Last Line: 12
22:55:45.315 : Resend: 13
22:55:45.321 : echo:endstops hit: Y:-0.24
22:55:45.326 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.326 : Resend: 17
22:55:45.334 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.334 : Resend: 17
22:55:45.337 : Resend: 13
22:55:45.340 : Error:No Line Number with checksum, Last Line: 12
22:55:45.340 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.340 : Resend: 13
22:55:45.343 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.343 : Resend: 13
22:55:45.346 : echo:endstops hit: Y:-0.25
22:55:45.351 : Resend: 13
22:55:45.355 : Error:No Line Number with checksum, Last Line: 12
22:55:45.355 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.355 : Resend: 13
22:55:45.359 : Error:No Line Number with checksum, Last Line: 12
22:55:45.363 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.363 : Resend: 13
22:55:45.366 : Error:No Line Number with checksum, Last Line: 12
22:55:45.367 : Error:0
22:55:45.367 : : Extruder switched off. MINTEMP triggered !
22:55:45.371 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.374 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.374 : Resend: 13
22:55:45.388 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.388 : Resend: 13
22:55:45.395 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.395 : Resend: 13
22:55:45.400 : echo:endstops hit: Y:-0.26
22:55:45.404 : Resend: 13
22:55:45.407 : Error:No Line Number with checksum, Last Line: 12
22:55:45.408 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.408 : Resend: 13
22:55:45.416 : echo:endstops hit: Y:-0.27
22:55:45.416 : Resend: 13
22:55:45.420 : Error:No Line Number with checksum, Last Line: 12
22:55:45.424 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.424 : Resend: 13
22:55:45.427 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.428 : Resend: 13
22:55:45.432 : echo:Unknown command: "60"
22:55:45.437 : echo:endstops hit: Y:-0.29
22:55:45.441 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.441 : Resend: 17
22:55:45.444 : Error:No Line Number with checksum, Last Line: 16
22:55:45.444 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.444 : Resend: 17
22:55:45.449 : Resend: 13
22:55:45.452 : Error:No Line Number with checksum, Last Line: 12
22:55:45.453 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.453 : Resend: 13
22:55:45.456 : Error:No Line Number with checksum, Last Line: 12
22:55:45.461 : echo:endstops hit: Y:-0.30
22:55:45.465 : Resend: 13
22:55:45.469 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.469 : Resend: 13
22:55:45.477 : echo:endstops hit: Y:-0.31
22:55:45.477 : Resend: 13
22:55:45.481 : echo:Unknown command: "120"
22:55:45.485 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.485 : Resend: 13
22:55:45.488 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.488 : Resend: 13
22:55:45.491 : Error:No Line Number with checksum, Last Line: 12
22:55:45.493 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.493 : Resend: 13
22:55:45.497 : Error:No Line Number with checksum, Last Line: 12
22:55:45.497 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.497 : Resend: 13
22:55:45.502 : echo:Unknown command: Error:0
22:55:45.502 : : Extruder switched off. MINTEMP triggered !
22:55:45.506 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.506 : "k"
22:55:45.510 : Error:No Line Number with checksum, Last Line: 12
22:55:45.514 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.514 : Resend: 13
22:55:45.517 : echo:Unknown command: "0"
22:55:45.526 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.530 : Resend: 13
22:55:45.535 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.535 : Resend: 13
22:55:45.543 : echo:endstops hit: Y:-0.32
22:55:45.543 : Resend: 13
22:55:45.547 : Error:No Line Number with checksum, Last Line: 12
22:55:45.552 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.552 : Resend: 13
22:55:45.555 : Error:No Line Number with checksum, Last Line: 12
22:55:45.555 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.555 : Resend: 13
22:55:45.564 : echo:endstops hit: Y:-0.34
22:55:45.568 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.568 : Resend: 17
22:55:45.571 : Error:No Line Number with checksum, Last Line: 16
22:55:45.576 : Resend: 13
22:55:45.579 : Error:No Line Number with checksum, Last Line: 12
22:55:45.580 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.580 : Resend: 13
22:55:45.587 : echo:endstops hit: Y:-0.35
22:55:45.588 : Resend: 13
22:55:45.597 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.597 : Resend: 13
22:55:45.600 : Error:No Line Number with checksum, Last Line: 12
22:55:45.600 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.600 : Resend: 13
22:55:45.609 : echo:endstops hit: Y:-0.36
22:55:45.613 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.613 : Resend: 17
22:55:45.616 : Error:No Line Number with checksum, Last Line: 16
22:55:45.621 : Resend: 13
22:55:45.624 : Error:No Line Number with checksum, Last Line: 12
22:55:45.625 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.625 : Resend: 13
22:55:45.633 : echo:endstops hit: Y:-0.37
22:55:45.633 : Resend: 13
22:55:45.637 : Error:Line NumbError:0
22:55:45.641 : : Extruder switched off. MINTEMP triggered !
22:55:45.645 : Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.645 : er is not Last Line Number+1, Last Line: 12
22:55:45.645 : Resend: 13
22:55:45.657 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.662 : Resend: 13
22:55:45.665 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.665 : Resend: 13
22:55:45.670 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.670 : Resend: 13
22:55:45.674 : Error:No Line Number with checksum, Last Line: 12
22:55:45.674 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.674 : Resend: 13
22:55:45.679 : Error:No Line Number with checksum, Last Line: 12
22:55:45.679 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.679 : Resend: 13
22:55:45.684 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.684 : Resend: 13
22:55:45.690 : Error:No Line Number with checksum, Last Line: 12
22:55:45.690 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.690 : Resend: 13
22:55:45.695 : Receiving only error messages. Stopped communication.
Here is my firmware as it is now:
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
// This configurtion file contains the basic settings.
// Advanced settings can be found in Configuration_adv.h
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
//User specified version info of this build to display in [Pronterface, etc] terminal window during startup.
//Implementation of an idea by Prof Braino to inform user that any changes made
//to this build by the user have been successfully uploaded into firmware.
#define STRING_VERSION_CONFIG_H __DATE__ "8-15-13" __TIME__ // build date and time
#define STRING_CONFIG_H_AUTHOR "(FOLGER TECH, 8 i3 Prusa Config)" //Who made the changes.
// SERIAL_PORT selects which serial port should be used for communication with the host.
// This allows the connection of wireless adapters (for instance) to non-default port pins.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
#define SERIAL_PORT 0
// This determines the communication speed of the printer
#define BAUDRATE 250000
//#define BAUDRATE 115200
//// The following define selects which electronics board you have. Please choose the one that matches your setup
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
// 11 = Gen7 v1.1, v1.2 = 11
// 12 = Gen7 v1.3
// 13 = Gen7 v1.4
// 3 = MEGA/RAMPS up to 1.2 = 3
// 33 = RAMPS 1.3 (Power outputs: Extruder, Bed, Fan)
// 34 = RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Bed)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
// 6 = Sanguinololu < 1.2
// 62 = Sanguinololu 1.2 and above
// 63 = Melzi
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
// 8 = Teensylu
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 9 = Gen3+
// 70 = Megatronics
// 90 = Alpha OMCA board
// 91 = Final OMCA board
// 301 = Rambo
#ifndef MOTHERBOARD
#define MOTHERBOARD 33
#endif
//// The following define selects which power supply you have. Please choose the one that matches your setup
// 1 = ATX
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
#define POWER_SUPPLY 1
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
//
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
//
//// Temperature sensor settings:
// -2 is thermocouple with MAX6675 (only for sensor 0)
// -1 is thermocouple with AD595
// 0 is not used
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
// 3 is mendel-parts thermistor (4.7k pullup)
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan) (4.7k pullup)
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
//
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
// (but gives greater accuracy and more stable PID)
// 51 is 100k thermistor - EPCOS (1k pullup)
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan) (1k pullup)
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_BED 1
// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 10 // (seconds)
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
#define TEMP_WINDOW 1 // (degC) Window around target to start the recidency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5
#define HEATER_1_MINTEMP 5
#define HEATER_2_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
// PID settings:
// Comment the following line to disable PID and enable bang-bang.
#define PIDTEMP
#define PID_MAX 256 // limits current to nozzle; 256=full current
#ifdef PIDTEMP
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID
#define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
// Ultimaker
#define DEFAULT_Kp 22.2
#define DEFAULT_Ki 1.08
#define DEFAULT_Kd 114
// Makergear
// #define DEFAULT_Kp 7.0
// #define DEFAULT_Ki 0.1
// #define DEFAULT_Kd 12
// Mendel Parts V9 on 12V
// #define DEFAULT_Kp 63.0
// #define DEFAULT_Ki 2.25
// #define DEFAULT_Kd 440
#endif // PIDTEMP
// Bed Temperature Control
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
//
// uncomment this to enable PID on the bed. It uses the same ferquency PWM as the extruder.
// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
// If your configuration is significantly different than this and you don't understand the issues involved, you proabaly
// shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below.
//#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING
// This sets the max power delived to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
// setting this to anything other than 256 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
#define MAX_BED_POWER 256 // limits duty cycle to bed; 256=full current
#ifdef PIDTEMPBED
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, argressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 10.00
#define DEFAULT_bedKi .023
#define DEFAULT_bedKd 305.4
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from pidautotune
// #define DEFAULT_bedKp 97.1
// #define DEFAULT_bedKi 1.41
// #define DEFAULT_bedKd 1675.16
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#endif // PIDTEMPBED
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
//#define PREVENT_DANGEROUS_EXTRUDE
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
//#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MINTEMP 1
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// Uncomment the following line to enable CoreXY kinematics
// #define COREXY
// corse Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
//#define ENDSTOPPULLUP_ZMIN
#endif
#ifdef ENDSTOPPULLUPS
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN
#endif
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
#define DISABLE_MAX_ENDSTOPS
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruders
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
// Travel limits after homing
#define X_MAX_POS 190
#define X_MIN_POS 0
#define Y_MAX_POS 190
#define Y_MIN_POS 0
#define Z_MAX_POS 190
#define Z_MIN_POS 0
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
//Manual homing switch locations:
#define MANUAL_X_HOME_POS 0
#define MANUAL_Y_HOME_POS 0
#define MANUAL_Z_HOME_POS 0
//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
// default settings //#define _AXIS_STEP_PER_UNIT {93.74, 94.184, 2564.1, 700} from sprinter for printrboard
// X, Y, Z, E steps per unit - Metric Prusa Mendel with Wade Extruder: (current setting / actual reading * 100)
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,600} // default steps per unit for prusa i3 rework
#define DEFAULT_MAX_FEEDRATE {500, 500, 2, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {2000,2000,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//
#define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
#define DEFAULT_EJERK 5.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
// EEPROM
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support
//#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can.
//#define EEPROM_CHITCHAT
//LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
//#define ULTIPANEL //the ultipanel as on thingiverse
// The RepRapDiscount Smart Controller (white PC
// [reprap.org]
#define REPRAP_DISCOUNT_SMART_CONTROLLER
// The GADGETS3D G3D LCD/SD Controller (blue PC
// [reprap.org]
//#define G3D_PANEL
//automatic expansion
#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define DOGLCD
#define U8GLIB_ST7920
#defube REPRAP_DISCOUNT_SMART_CONTROLLER
#endif
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#ifdef ULTIPANEL
// #define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
#define LCD_HEIGHT 4
#else //no panel but just lcd
#ifdef ULTRA_LCD
#define LCD_WIDTH 16
#define LCD_HEIGHT 2
#endif
#endif
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
//#define FAST_PWM_FAN
// M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: [www.doc-diy.net]
// #define PHOTOGRAPH_PIN 23
// SF send wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX
#include "Configuration_adv.h"
#include "thermistortables.h"
#endif //__CONFIGURATION_H
22:54:48.709 : No start signal detected - forcing start
22:54:56.470 : No start signal detected - forcing start
22:55:34.967 : start
22:55:34.967 : echo:Marlin 1.0.0
22:55:34.971 : echo: Last Updated: Feb 14 20158-15-1322:55:13 | Author: (FOLGER TECH, 8 i3 Prusa Config)
22:55:34.971 : Compiled: Feb 14 2015
22:55:34.971 : echo: Free Memory: 5516 PlannerBufferBytes: 1232
22:55:35.233 : Error:0
22:55:35.237 : : Extruder switched off. MINTEMP triggered !
22:55:35.242 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:35.414 : echo:Unknown command: ""
22:55:36.090 : FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:[www.mendel-parts.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:FolgerTech EXTRUDER_COUNT:1
22:55:36.097 : echo:Active Extruder: 0
22:55:36.105 : echo:Active Extruder: 0
22:55:40.624 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.665 : Resend: 1
22:55:44.679 : FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:[www.mendel-parts.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:FolgerTech EXTRUDER_COUNT:1
22:55:44.684 : echo:Active Extruder: 0
22:55:44.684 : Error:0
22:55:44.687 : : Extruder switched off. MINTEMP triggered !
22:55:44.691 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:44.695 : Error:No Checksum with line number, Last Line: 7
22:55:44.695 : Resend: 8
22:55:44.698 : Error:Line Number is not Last Line Number+1, Last Line: 7
22:55:44.698 : Resend: 8
22:55:44.703 : echo:Active Extruder: 0
22:55:44.707 : Error:Line Number is not Last Line Number+1, Last Line: 11
22:55:44.711 : Resend: 12
22:55:44.714 : Error:No Line Number with checksum, Last Line: 11
22:55:44.715 : Error:Line Number is not Last Line Number+1, Last Line: 11
22:55:44.715 : Resend: 12
22:55:44.723 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.728 : Error:No Line Number with checksum, Last Line: 15
22:55:44.728 : Error:Line Number is not Last Line Number+1, Last Line: 15
22:55:44.728 : Resend: 16
22:55:44.735 : Resend: 7
22:55:44.739 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.744 : Resend: 7
22:55:44.748 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.748 : Resend: 7
22:55:44.757 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.757 : Resend: 10
22:55:44.760 : Error:No Line Number with checksum, Last Line: 9
22:55:44.761 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.761 : Resend: 10
22:55:44.765 : echo:Active Extruder: 0
22:55:44.769 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.769 : Resend: 14
22:55:44.773 : echo:Unknown command: "6"
22:55:44.773 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.773 : Resend: 14
22:55:44.781 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.781 : Resend: 14
22:55:44.786 : echo:endstops hit: Y:-0.01
22:55:44.786 : Resend: 7
22:55:44.790 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.790 : Resend: 7
22:55:44.794 : Error:No Line Number with checksum, Last Line: 6
22:55:44.794 : Error:Line Number is not Last Line Number+1, Last Line: 6
22:55:44.794 : Resend: 7
22:55:44.798 : Error:No Line Number with checksum, Last Line: 6
22:55:44.798 : Error:checksum mismatch, Last Line: 6
22:55:44.801 : Resend: 7
22:55:44.810 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.810 : Resend: 10
22:55:44.813 : Error:Line Number is not Last Line Number+1, Last Line: 9
22:55:44.813 : Resend: 10
22:55:44.818 : echo:Active Extruder: 0
22:55:44.822 : Error:0
22:55:44.822 : : Extruder switched off. MINTEMP triggered !
22:55:44.826 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:44.830 : Error:Line Number is not Last Line Number+1, Last Line: 13
22:55:44.830 : Resend: 14
22:55:44.842 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.844 : Resend: 13
22:55:44.850 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.850 : Resend: 13
22:55:44.855 : echo:endstops hit: Y:-0.03
22:55:44.859 : Resend: 13
22:55:44.862 : Error:No Line Number with checksum, Last Line: 12
22:55:44.862 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.862 : Resend: 13
22:55:44.871 : echo:endstops hit: Y:-0.04
22:55:44.871 : Resend: 13
22:55:44.879 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.879 : Resend: 13
22:55:44.883 : Error:No Line Number with checksum, Last Line: 12
22:55:44.883 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.883 : Resend: 13
22:55:44.892 : echo:endstops hit: Y:-0.05
22:55:44.896 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.896 : Resend: 17
22:55:44.899 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.899 : Resend: 17
22:55:44.904 : Resend: 13
22:55:44.907 : Error:No Line Number with checksum, Last Line: 12
22:55:44.908 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.908 : Resend: 13
22:55:44.912 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.912 : Resend: 13
22:55:44.917 : Error:No Line Number with checksum, Last Line: 12
22:55:44.917 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.917 : Resend: 13
22:55:44.922 : Error:No Line Number with checksum, Last Line: 12
22:55:44.924 : echo:endstops hit: Y:-0.06
22:55:44.928 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.928 : Resend: 17
22:55:44.937 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.937 : Resend: 17
22:55:44.940 : Error:No Line Number with checksum, Last Line: 16
22:55:44.941 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:44.941 : Resend: 17
22:55:44.945 : Resend: 13
22:55:44.950 : Error:No Line Number with checksum, LasN17 M99 12
22:55:44.950 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.950 : Resend: 13
22:55:44.953 : Error:No Line Number with checksum, Last Line: 12
22:55:44.953 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.953 : Resend: 13
22:55:44.957 : Error:No Line Number with checksum, Last Line:Error:0
22:55:44.957 : : Extruder switched off. MINTEMP triggered !
22:55:44.961 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:44.965 : 12
22:55:44.965 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.965 : Resend: 13
22:55:44.978 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:44.982 : Resend: 13
22:55:44.986 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:44.986 : Resend: 13
22:55:44.995 : echo:endstops hit: Y:-0.08
22:55:44.995 : Resend: 13
22:55:44.998 : Error:No Line Number with checksum, Last Line: 12
22:55:45.002 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.002 : Resend: 13
22:55:45.005 : Error:No Line Number with checksum, Last Line: 12
22:55:45.006 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.006 : Resend: 13
22:55:45.014 : echo:endstops hit: Y:-0.09
22:55:45.018 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.019 : Resend: 17
22:55:45.022 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.022 : Resend: 17
22:55:45.027 : Resend: 13
22:55:45.030 : Error:No Line Number with checksum, Last Line: 12
22:55:45.031 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.031 : Resend: 13
22:55:45.036 : echo:Unknown command: "20"
22:55:45.036 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.036 : Resend: 13
22:55:45.039 : echo:Unknown command: "4"
22:55:45.039 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.039 : Resend: 13
22:55:45.043 : Error:No Line Number with checksum, Last Line: 12
22:55:45.043 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.047 : Resend: 13
22:55:45.050 : Error:No Line Number with checksum, Last Line: 12
22:55:45.051 : echo:endstops hit: Y:-0.10
22:55:45.056 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.056 : Resend: 17
22:55:45.059 : Error:No Line Number with checksum, Last Line: 16
22:55:45.063 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.063 : Resend: 17
22:55:45.066 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.066 : Resend: 17
22:55:45.071 : Resend: 13
22:55:45.075 : Error:No Line Number with checksum, Last Line: 12
22:55:45.075 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.075 : Resend: 13
22:55:45.084 : echo:endstops hit: Y:-0.11
22:55:45.088 : Resend: 13
22:55:45.093 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.093 : Resend: 13
22:55:45.096 : Error:0
22:55:45.097 : : Extruder switched off. MINTEMP triggered !
22:55:45.101 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:45.101 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.104 : Resend: 13
22:55:45.117 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.117 : Resend: 13
22:55:45.125 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.125 : Resend: 13
22:55:45.130 : echo:endstops hit: Y:-0.12
22:55:45.134 : Resend: 13
22:55:45.137 : Error:No Line Number with checksum, Last Line: 12
22:55:45.137 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.137 : Resend: 13
22:55:45.146 : echo:endstops hit: Y:-0.14
22:55:45.146 : Resend: 13
22:55:45.154 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.154 : Resend: 13
22:55:45.157 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.157 : Resend: 13
22:55:45.166 : echo:endstops hit: Y:-0.15
22:55:45.170 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.170 : Resend: 17
22:55:45.174 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.174 : Resend: 17
22:55:45.179 : Resend: 13
22:55:45.183 : Error:No Line Number with checksum, Last Line: 12
22:55:45.183 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.183 : Resend: 13
22:55:45.186 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.186 : Resend: 13
22:55:45.191 : echo:endstops hit: Y:-0.16
22:55:45.195 : Resend: 13
22:55:45.200 : echo:endstops hit: Y:-0.17
22:55:45.203 : Resend: 13
22:55:45.207 : echo:endstops hit: Y:-0.19
22:55:45.211 : Resend: 13
22:55:45.214 : Error:No Line Number with checksum, Last Line: 12
22:55:45.215 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.215 : Resend: 13
22:55:45.223 : echo:endstops hit: Y:-0.20
22:55:45.223 : Resend: 13
22:55:45.227 : echo:Unknown command: "20"
22:55:45.227 : Error:Line Number is not Last LError:0
22:55:45.232 : : Extruder switched off. MINTEMP triggered !
22:55:45.236 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:45.236 : ine Number+1, Last Line: 12
22:55:45.236 : Resend: 13
22:55:45.248 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.252 : Resend: 13
22:55:45.256 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.256 : Resend: 13
22:55:45.264 : echo:endstops hit: Y:-0.21
22:55:45.265 : Resend: 13
22:55:45.268 : echo:Unknown command: "20"
22:55:45.273 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.273 : Resend: 13
22:55:45.276 : Error:No Line Number with checksum, Last Line: 12
22:55:45.277 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.277 : Resend: 13
22:55:45.285 : echo:endstops hit: Y:-0.22
22:55:45.289 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.289 : Resend: 17
22:55:45.292 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.292 : Resend: 17
22:55:45.297 : Resend: 13
22:55:45.300 : Error:No Line Number with checksum, Last Line: 12
22:55:45.302 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.302 : Resend: 13
22:55:45.305 : echo:Unknown command: "20"
22:55:45.306 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.306 : Resend: 13
22:55:45.310 : Error:No Line Number with checksum, Last Line: 12
22:55:45.310 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.310 : Resend: 13
22:55:45.315 : Error:No Line Number with checksum, Last Line: 12
22:55:45.315 : Error:No Checksum with line number, Last Line: 12
22:55:45.315 : Resend: 13
22:55:45.321 : echo:endstops hit: Y:-0.24
22:55:45.326 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.326 : Resend: 17
22:55:45.334 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.334 : Resend: 17
22:55:45.337 : Resend: 13
22:55:45.340 : Error:No Line Number with checksum, Last Line: 12
22:55:45.340 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.340 : Resend: 13
22:55:45.343 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.343 : Resend: 13
22:55:45.346 : echo:endstops hit: Y:-0.25
22:55:45.351 : Resend: 13
22:55:45.355 : Error:No Line Number with checksum, Last Line: 12
22:55:45.355 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.355 : Resend: 13
22:55:45.359 : Error:No Line Number with checksum, Last Line: 12
22:55:45.363 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.363 : Resend: 13
22:55:45.366 : Error:No Line Number with checksum, Last Line: 12
22:55:45.367 : Error:0
22:55:45.367 : : Extruder switched off. MINTEMP triggered !
22:55:45.371 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:45.374 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.374 : Resend: 13
22:55:45.388 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.388 : Resend: 13
22:55:45.395 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.395 : Resend: 13
22:55:45.400 : echo:endstops hit: Y:-0.26
22:55:45.404 : Resend: 13
22:55:45.407 : Error:No Line Number with checksum, Last Line: 12
22:55:45.408 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.408 : Resend: 13
22:55:45.416 : echo:endstops hit: Y:-0.27
22:55:45.416 : Resend: 13
22:55:45.420 : Error:No Line Number with checksum, Last Line: 12
22:55:45.424 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.424 : Resend: 13
22:55:45.427 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.428 : Resend: 13
22:55:45.432 : echo:Unknown command: "60"
22:55:45.437 : echo:endstops hit: Y:-0.29
22:55:45.441 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.441 : Resend: 17
22:55:45.444 : Error:No Line Number with checksum, Last Line: 16
22:55:45.444 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.444 : Resend: 17
22:55:45.449 : Resend: 13
22:55:45.452 : Error:No Line Number with checksum, Last Line: 12
22:55:45.453 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.453 : Resend: 13
22:55:45.456 : Error:No Line Number with checksum, Last Line: 12
22:55:45.461 : echo:endstops hit: Y:-0.30
22:55:45.465 : Resend: 13
22:55:45.469 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.469 : Resend: 13
22:55:45.477 : echo:endstops hit: Y:-0.31
22:55:45.477 : Resend: 13
22:55:45.481 : echo:Unknown command: "120"
22:55:45.485 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.485 : Resend: 13
22:55:45.488 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.488 : Resend: 13
22:55:45.491 : Error:No Line Number with checksum, Last Line: 12
22:55:45.493 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.493 : Resend: 13
22:55:45.497 : Error:No Line Number with checksum, Last Line: 12
22:55:45.497 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.497 : Resend: 13
22:55:45.502 : echo:Unknown command: Error:0
22:55:45.502 : : Extruder switched off. MINTEMP triggered !
22:55:45.506 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:45.506 : "k"
22:55:45.510 : Error:No Line Number with checksum, Last Line: 12
22:55:45.514 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.514 : Resend: 13
22:55:45.517 : echo:Unknown command: "0"
22:55:45.526 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.530 : Resend: 13
22:55:45.535 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.535 : Resend: 13
22:55:45.543 : echo:endstops hit: Y:-0.32
22:55:45.543 : Resend: 13
22:55:45.547 : Error:No Line Number with checksum, Last Line: 12
22:55:45.552 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.552 : Resend: 13
22:55:45.555 : Error:No Line Number with checksum, Last Line: 12
22:55:45.555 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.555 : Resend: 13
22:55:45.564 : echo:endstops hit: Y:-0.34
22:55:45.568 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.568 : Resend: 17
22:55:45.571 : Error:No Line Number with checksum, Last Line: 16
22:55:45.576 : Resend: 13
22:55:45.579 : Error:No Line Number with checksum, Last Line: 12
22:55:45.580 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.580 : Resend: 13
22:55:45.587 : echo:endstops hit: Y:-0.35
22:55:45.588 : Resend: 13
22:55:45.597 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.597 : Resend: 13
22:55:45.600 : Error:No Line Number with checksum, Last Line: 12
22:55:45.600 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.600 : Resend: 13
22:55:45.609 : echo:endstops hit: Y:-0.36
22:55:45.613 : Error:Line Number is not Last Line Number+1, Last Line: 16
22:55:45.613 : Resend: 17
22:55:45.616 : Error:No Line Number with checksum, Last Line: 16
22:55:45.621 : Resend: 13
22:55:45.624 : Error:No Line Number with checksum, Last Line: 12
22:55:45.625 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.625 : Resend: 13
22:55:45.633 : echo:endstops hit: Y:-0.37
22:55:45.633 : Resend: 13
22:55:45.637 : Error:Line NumbError:0
22:55:45.641 : : Extruder switched off. MINTEMP triggered !
22:55:45.645 : Error
rinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)22:55:45.645 : er is not Last Line Number+1, Last Line: 12
22:55:45.645 : Resend: 13
22:55:45.657 : Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
22:55:45.662 : Resend: 13
22:55:45.665 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.665 : Resend: 13
22:55:45.670 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.670 : Resend: 13
22:55:45.674 : Error:No Line Number with checksum, Last Line: 12
22:55:45.674 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.674 : Resend: 13
22:55:45.679 : Error:No Line Number with checksum, Last Line: 12
22:55:45.679 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.679 : Resend: 13
22:55:45.684 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.684 : Resend: 13
22:55:45.690 : Error:No Line Number with checksum, Last Line: 12
22:55:45.690 : Error:Line Number is not Last Line Number+1, Last Line: 12
22:55:45.690 : Resend: 13
22:55:45.695 : Receiving only error messages. Stopped communication.
Here is my firmware as it is now:
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
// This configurtion file contains the basic settings.
// Advanced settings can be found in Configuration_adv.h
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
//User specified version info of this build to display in [Pronterface, etc] terminal window during startup.
//Implementation of an idea by Prof Braino to inform user that any changes made
//to this build by the user have been successfully uploaded into firmware.
#define STRING_VERSION_CONFIG_H __DATE__ "8-15-13" __TIME__ // build date and time
#define STRING_CONFIG_H_AUTHOR "(FOLGER TECH, 8 i3 Prusa Config)" //Who made the changes.
// SERIAL_PORT selects which serial port should be used for communication with the host.
// This allows the connection of wireless adapters (for instance) to non-default port pins.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
#define SERIAL_PORT 0
// This determines the communication speed of the printer
#define BAUDRATE 250000
//#define BAUDRATE 115200
//// The following define selects which electronics board you have. Please choose the one that matches your setup
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
// 11 = Gen7 v1.1, v1.2 = 11
// 12 = Gen7 v1.3
// 13 = Gen7 v1.4
// 3 = MEGA/RAMPS up to 1.2 = 3
// 33 = RAMPS 1.3 (Power outputs: Extruder, Bed, Fan)
// 34 = RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Bed)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
// 6 = Sanguinololu < 1.2
// 62 = Sanguinololu 1.2 and above
// 63 = Melzi
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
// 8 = Teensylu
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 9 = Gen3+
// 70 = Megatronics
// 90 = Alpha OMCA board
// 91 = Final OMCA board
// 301 = Rambo
#ifndef MOTHERBOARD
#define MOTHERBOARD 33
#endif
//// The following define selects which power supply you have. Please choose the one that matches your setup
// 1 = ATX
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
#define POWER_SUPPLY 1
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
//
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
//
//// Temperature sensor settings:
// -2 is thermocouple with MAX6675 (only for sensor 0)
// -1 is thermocouple with AD595
// 0 is not used
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
// 3 is mendel-parts thermistor (4.7k pullup)
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan) (4.7k pullup)
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
//
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
// (but gives greater accuracy and more stable PID)
// 51 is 100k thermistor - EPCOS (1k pullup)
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan) (1k pullup)
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_BED 1
// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 10 // (seconds)
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
#define TEMP_WINDOW 1 // (degC) Window around target to start the recidency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5
#define HEATER_1_MINTEMP 5
#define HEATER_2_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
// PID settings:
// Comment the following line to disable PID and enable bang-bang.
#define PIDTEMP
#define PID_MAX 256 // limits current to nozzle; 256=full current
#ifdef PIDTEMP
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID
#define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
// Ultimaker
#define DEFAULT_Kp 22.2
#define DEFAULT_Ki 1.08
#define DEFAULT_Kd 114
// Makergear
// #define DEFAULT_Kp 7.0
// #define DEFAULT_Ki 0.1
// #define DEFAULT_Kd 12
// Mendel Parts V9 on 12V
// #define DEFAULT_Kp 63.0
// #define DEFAULT_Ki 2.25
// #define DEFAULT_Kd 440
#endif // PIDTEMP
// Bed Temperature Control
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
//
// uncomment this to enable PID on the bed. It uses the same ferquency PWM as the extruder.
// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
// If your configuration is significantly different than this and you don't understand the issues involved, you proabaly
// shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below.
//#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING
// This sets the max power delived to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
// setting this to anything other than 256 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
#define MAX_BED_POWER 256 // limits duty cycle to bed; 256=full current
#ifdef PIDTEMPBED
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, argressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 10.00
#define DEFAULT_bedKi .023
#define DEFAULT_bedKd 305.4
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from pidautotune
// #define DEFAULT_bedKp 97.1
// #define DEFAULT_bedKi 1.41
// #define DEFAULT_bedKd 1675.16
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#endif // PIDTEMPBED
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
//#define PREVENT_DANGEROUS_EXTRUDE
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
//#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MINTEMP 1
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// Uncomment the following line to enable CoreXY kinematics
// #define COREXY
// corse Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
//#define ENDSTOPPULLUP_ZMIN
#endif
#ifdef ENDSTOPPULLUPS
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN
#endif
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops.
#define DISABLE_MAX_ENDSTOPS
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruders
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false // For all extruders
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
// Travel limits after homing
#define X_MAX_POS 190
#define X_MIN_POS 0
#define Y_MAX_POS 190
#define Y_MIN_POS 0
#define Z_MAX_POS 190
#define Z_MIN_POS 0
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
// The position of the homing switches
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
//Manual homing switch locations:
#define MANUAL_X_HOME_POS 0
#define MANUAL_Y_HOME_POS 0
#define MANUAL_Z_HOME_POS 0
//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
// default settings //#define _AXIS_STEP_PER_UNIT {93.74, 94.184, 2564.1, 700} from sprinter for printrboard
// X, Y, Z, E steps per unit - Metric Prusa Mendel with Wade Extruder: (current setting / actual reading * 100)
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,600} // default steps per unit for prusa i3 rework
#define DEFAULT_MAX_FEEDRATE {500, 500, 2, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {2000,2000,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//
#define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
#define DEFAULT_EJERK 5.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
// EEPROM
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support
//#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can.
//#define EEPROM_CHITCHAT
//LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
//#define ULTIPANEL //the ultipanel as on thingiverse
// The RepRapDiscount Smart Controller (white PC
// [reprap.org]
#define REPRAP_DISCOUNT_SMART_CONTROLLER
// The GADGETS3D G3D LCD/SD Controller (blue PC
// [reprap.org]
//#define G3D_PANEL
//automatic expansion
#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define DOGLCD
#define U8GLIB_ST7920
#defube REPRAP_DISCOUNT_SMART_CONTROLLER
#endif
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#ifdef ULTIPANEL
// #define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
#define LCD_HEIGHT 4
#else //no panel but just lcd
#ifdef ULTRA_LCD
#define LCD_WIDTH 16
#define LCD_HEIGHT 2
#endif
#endif
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
//#define FAST_PWM_FAN
// M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: [www.doc-diy.net]
// #define PHOTOGRAPH_PIN 23
// SF send wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX
#include "Configuration_adv.h"
#include "thermistortables.h"
#endif //__CONFIGURATION_H
Sorry, only registered users may post in this forum.