Looking for an qualified USA/Canada distributor (RADDS-32-Bit Electronic)

Hi reprapers,

I would like to get help to get a Distributor for North America, I can give you 35% off (minimum 10 pieces, 40% discount for 100 and up).
I would like to send you 10 RADDS v1.1 Shield. If you have delivered/sell it,
you pay me than this 10 RADDS, and I would send you minimum 10 RADDS again and so on..
I have to give you a deep knowlege training for the RADDS + Repetier-Firmware etc...
So the Distributor has to give the first/second Level Support for his reprap-ers/customers.

My Dream is, to give the reprap community a precision, fast and very stable DIY Electronic-Set for the possibility of a High-Quality 3D-Print-Result.
Arduino Due, because you have the possibility to optimize and add features with the Arduino IDE without deep programming knowlage...
In Last Line, I would like to offer 3 Sets:

Economic Set:
Arduino DUE+RADDS v1.1+ 3x1/32 DRV8825 Microstepperdriver+ LCD-Display+ Cable-Set = 170 Euro

Standard Set:
Arduino DUE+RADDS v1.1+ 3x1/128 Microstepperdriver+ LCD-Display+ Cable-Set = 250 Euro

Premium Set (+ opt1. , opt2. opt1+7"LCD-Display ):
UDOO Quad+RADDS v1.1(Included with the SD-image preconfigured Linux+Repetier-Firmware -> udoo-reprap )+ 3x1/128 Microstepperdriver+ LCD-Display+ Cable-Set+ 4x Nema17, 0.9deg (400 Steps) = 350 Euro
[sourceforge.net]

Premium Set advanced = Premium Set +Sata 256GB SSD+Webcam
Premium Set Profi = Premium Set advanced+ 7"LCD-Display

I have buildings for RADDS Standard-Set in Progress (DeltaMax 3D-Printer and OX-Openbuilds CNC-Router/3D-Printer)
This I would like to published and discribe this with step-by-step howto-doku ( Sptember 2014) .
[www.openbuilds.com]

This is my Vision.

Have Fun
angelo

---

Mein Club: [hackerspace-ffm.de]
RADDS-Shield -> Commercial [max3dshop.org]

Hi angelo!

Why do you want to include just 3 stepper drivers? typo?

32-Bit Electronic make sense for x/y core or Delta (speed).
the Stepperdriver 1/128 more for a excellent print result and a better positioning (quality).

In regular 1/128 drivers for Extruder make no sense (1/16 -1/32 personaly i think it is enough).

Sets are only a idea .. inspirations are very welcome.
By the Way .. next Week arive the LCD Displays (tested and stable release) for the RADDS:

---

Mein Club: [hackerspace-ffm.de]
RADDS-Shield -> Commercial [max3dshop.org]

Hi Angelo,

As your information that Radds V1.1 has ability to connect with LCD and SD card. This is much better than Ramps-FD now.

I have one question about the RADDS V1.1. Can I use RADDS v1.1 with Arduino DUE and UDOO without any cahnge? Or I have to change some wires for UDOO?

Hi Alvin,

You can plug RADDS v1.1 without any Change to The Arduino DUE and UDOO Quad.
I think also with RAMPS-FD you can make it.

Please read The UDOO manual for More Information (Jumper J18).
[www.udoo.org]

A small RADDS v1.1 Dokumentation you can find here:

[max3dshop.org]

Edited 4 time(s). Last edit at 10/13/2014 12:19AM by angelo.

---

Mein Club: [hackerspace-ffm.de]
RADDS-Shield -> Commercial [max3dshop.org]