Bonjour,
Après avoir télécharger le repetier firmware et modifier les valeurs dans le fichiers configuration.h, le fichier compile avec un nombre incalculable d'erreur, notamment :
In file included from /Repetier.h:264,
from Commands.cpp:22:
/HAL.h:71:21: error: Arduino.h: No such file or directory
In file included from /Repetier.h:264,
from Commands.cpp:22:
HAL.h:192: error: conflicting return type specified for 'virtual size_t RFHardwareSerial::write(uint8_t)'
C:\Program Files (x86)\Arduino\hardware\Gen7\cores\arduino/Print.h:37: error: overriding 'virtual void Print::write(uint8_t)'
/HAL.h: In static member function 'static void HAL::digitalWrite(uint8_t, uint8_t)':
HAL.h:449: error: '::digitalWrite' has not been declared
/HAL.h: In static member function 'static uint8_t HAL::digitalRead(uint8_t)':
HAL.h:453: error: '::digitalRead' has not been declared
/HAL.h: In static member function 'static void HAL::pinMode(uint8_t, uint8_t)':
HAL.h:457: error: '::pinMode' has not been declared
/HAL.h: In static member function 'static void HAL::delayMicroseconds(unsigned int)':
HAL.h:462: error: '::delayMicroseconds' has not been declared
/HAL.h: In static member function 'static void HAL::delayMilliseconds(unsigned int)':
HAL.h:466: error: '::delay' has not been declared
/HAL.h: In static member function 'static void HAL::tone(uint8_t, int)':
HAL.h:470: error: '::tone' has not been declared
/HAL.h: In static member function 'static void HAL::noTone(uint8_t)':
HAL.h:474: error: '::noTone' has not been declared
/HAL.h: In static member function 'static void HAL::allowInterrupts()':
HAL.h:512: error: 'sei' was not declared in this scope
/HAL.h: In static member function 'static void HAL::forbidInterrupts()':
HAL.h:516: error: 'cli' was not declared in this scope
/HAL.h: In static member function 'static long unsigned int HAL::timeInMilliseconds()':
HAL.h:520: error: 'millis' was not declared in this scope
/HAL.h: In static member function 'static void HAL::spiInit(uint8_t)':
HAL.h:573: error: 'HIGH' was not declared in this scope
In file included from /Repetier.h:265,
from Commands.cpp:22:
/gcode.h: In member function 'float GCode::parseFloatValue(char*)':
gcode.h:147: error: 'strtod' was not declared in this scope
/gcode.h: In member function 'long int GCode::parseLongValue(char*)':
gcode.h:154: error: 'strtol' was not declared in this scope
In file included from /Repetier.h:356,
from Commands.cpp:22:
/Extruder.h: In static member function 'static void Extruder::step()':
Extruder.h:107: error: 'HIGH' was not declared in this scope
/Extruder.h: In static member function 'static void Extruder::unstep()':
Extruder.h:156: error: 'LOW' was not declared in this scope
In file included from /Repetier.h:385,
from Commands.cpp:22:
/Printer.h: In static member function 'static void Printer::endXYZSteps()':
Printer.h:534: error: 'LOW' was not declared in this scope
Printer.h:535: error: 'LOW' was not declared in this scope
Printer.h:536: error: 'LOW' was not declared in this scope
In file included from /Repetier.h:386,
from Commands.cpp:22:
/motion.h: In member function 'void PrintLine::startXStep()':
motion.h:501: error: 'HIGH' was not declared in this scope
/motion.h: In member function 'void PrintLine::startYStep()':
motion.h:541: error: 'HIGH' was not declared in this scope
/motion.h: In member function 'void PrintLine::startZStep()':
motion.h:577: error: 'HIGH' was not declared in this scope
Commands.cpp: In static member function 'static void Commands::setFanSpeed(int, bool)':
Commands.cpp:208: error: 'constrain' was not declared in this scope
Commands.cpp: In static member function 'static void Commands::executeGCode(GCode*)':
Commands.cpp:912: error: 'OUTPUT' was not declared in this scope
Commands.cpp:912: error: 'pinMode' was not declared in this scope
Commands.cpp:913: error: 'digitalWrite' was not declared in this scope
Commands.cpp:914: error: 'analogWrite' was not declared in this scope
Commands.cpp:961: error: 'abs' was not declared in this scope
Commands.cpp:1049: error: 'fabs' was not declared in this scope
Commands.cpp:1102: error: 'HIGH' was not declared in this scope
Commands.cpp:1102: error: 'LOW' was not declared in this scope
Commands.cpp:1109: error: 'LOW' was not declared in this scope
Commands.cpp:1109: error: 'HIGH' was not declared in this scope
et une erreur concernant un certain uint8_t ?
Quelqu'un aurait il déjà eu ce problème ?
Merci de votre réponse