RAMPS 1.3 with Techzone opto-endstops June 05, 2011 07:53PM |
Registered: 14 years ago Posts: 126 |
Re: RAMPS 1.3 with Techzone opto-endstops June 05, 2011 09:14PM |
Registered: 13 years ago Posts: 197 |
Re: RAMPS 1.3 with Techzone opto-endstops June 05, 2011 11:16PM |
Registered: 14 years ago Posts: 126 |
Re: RAMPS 1.3 with Techzone opto-endstops June 06, 2011 05:02AM |
Registered: 14 years ago Posts: 689 |
Re: RAMPS 1.3 with Techzone opto-endstops June 06, 2011 08:27AM |
Registered: 13 years ago Posts: 1,780 |
Re: RAMPS 1.3 with Techzone opto-endstops June 06, 2011 03:15PM |
Registered: 14 years ago Posts: 126 |
Re: RAMPS 1.3 with Techzone opto-endstops June 06, 2011 10:09PM |
Registered: 13 years ago Posts: 486 |
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 12:15PM |
Registered: 14 years ago Posts: 126 |
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 03:01PM |
Registered: 13 years ago Posts: 1,780 |
//Endstop Settings #define ENDSTOPPULLUPS 1 const bool ENDSTOPS_INVERTING = false; const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero. const bool max_software_endstops = true; //If true, axis won't move to coordinates greater than the defined lengths below. const int X_MAX_LENGTH = 220; const int Y_MAX_LENGTH = 220; const int Z_MAX_LENGTH = 100;
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 07:12PM |
Registered: 12 years ago Posts: 139 |
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 07:28PM |
Registered: 14 years ago Posts: 689 |
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 08:12PM |
Registered: 13 years ago Posts: 1,780 |
Re: RAMPS 1.3 with Techzone opto-endstops June 07, 2011 08:15PM |
Registered: 13 years ago Posts: 1,780 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 02:38AM |
Registered: 14 years ago Posts: 689 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 04:25AM |
Registered: 12 years ago Posts: 139 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 05:10AM |
Registered: 14 years ago Posts: 689 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 07:26AM |
Registered: 13 years ago Posts: 1,780 |
Quote
Nudel
brnrd Wrote:
-------------------------------------------------------
> @Nudel - how reproducible is the mechanical switch
> on the z-axis? I think the x and y is not that
>...
It's quite high actually, though far from perfect in the long run. When it was dialed in I think I adjusted it once every two-three days or something. And that was mostly needed because of hot end or carriage tweaks.
Quote
Nudel
Mine neither dean448. That means you need to have the physical pullup resistors as described on the wiki.
//endstop pullups #ifdef ENDSTOPPULLUPS if(X_MIN_PIN > -1) { pinMode(X_MIN_PIN,INPUT); digitalWrite(X_MIN_PIN,HIGH);} if(Y_MIN_PIN > -1) { pinMode(Y_MIN_PIN,INPUT); digitalWrite(Y_MIN_PIN,HIGH);} if(Z_MIN_PIN > -1) { pinMode(Z_MIN_PIN,INPUT); digitalWrite(Z_MIN_PIN,HIGH);} if(X_MAX_PIN > -1) { pinMode(X_MAX_PIN,INPUT); digitalWrite(X_MAX_PIN,HIGH);} if(Y_MAX_PIN > -1) { pinMode(Y_MAX_PIN,INPUT); digitalWrite(Y_MAX_PIN,HIGH);} if(Z_MAX_PIN > -1) { pinMode(Z_MAX_PIN,INPUT); digitalWrite(Z_MAX_PIN,HIGH);} #endif
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 07:53AM |
Registered: 14 years ago Posts: 689 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 08:08AM |
Registered: 13 years ago Posts: 1,780 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 08:12AM |
Registered: 13 years ago Posts: 1,780 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 07:49PM |
Registered: 12 years ago Posts: 139 |
Re: RAMPS 1.3 with Techzone opto-endstops June 08, 2011 09:38PM |
Registered: 13 years ago Posts: 1,780 |