Hi, I bought this printer: [
www.amazon.co.uk]
and I would like to flash the firmware.
The controller seem to be a ramps 1.4 with an arduino soldered on the board. It's written 'Borlee 3D' on it.
When I plug the usb cable, the driver installed is FTDI.
I opened arduino ide, selected the right port and Arduino mega 2560. When I upload the code, arduino receive the initialization sequence of marlin...
like this:
avrdude: Recv: s [73]
avrdude: Recv: e [65]
avrdude: Recv: t [74]
avrdude: Recv: t [74]
avrdude: Recv: i [69]
avrdude: Recv: n [6e]
avrdude: Recv: g [67]
avrdude: Recv: s [73]
avrdude: Recv: : [3a]
avrdude: Recv: . [0a]
avrdude: Recv: e [65]
avrdude: Recv: c [63]
avrdude: Recv: h [68]
avrdude: Recv: o [6f]
avrdude: Recv: : [3a]
avrdude: Recv: [20]
avrdude: Recv: [20]
avrdude: Recv: [20]
avrdude: Recv: M [4d]
avrdude: Recv: 3 [33]
avrdude: Recv: 0 [30]
avrdude: Recv: 1 [31]
avrdude: Recv: [20]
avrdude: Recv: P [50]
avrdude: Recv: 2 [32]
avrdude: Recv: 2 [32]
avrdude: Recv: . [2e]
avrdude: Recv: 2 [32]
avrdude: Recv: 0 [30]
avrdude: Recv: [20]
avrdude: Recv: I [49]
avrdude: Recv: 1 [31]
avrdude: Recv: . [2e]
avrdude: Recv: 0 [30]
avrdude: Recv: 8 [38]
avrdude: Recv: [20]
avrdude: Recv: D [44]
avrdude: Recv: 1 [31]
avrdude: Recv: 1 [31]
avrdude: Recv: 4 [34]
avrdude: Recv: . [2e]
avrdude: Recv: 0 [30]
avrdude: Recv: 0 [30]
avrdude: Recv: . [0a]
avrdude: Recv: e [65]
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv: c [63]
avrdude: Recv: h [68]
avrdude: Recv: o [6f]
avrdude: Recv: : [3a]
avrdude: Recv: S [53]
avrdude: Recv: D [44]
avrdude: Recv: [20]
avrdude: Recv: i [69]
avrdude: Recv: n [6e]
avrdude: Recv: i [69]
avrdude: Recv: t [74]
avrdude: Recv: [20]
avrdude: Recv: f [66]
avrdude: Recv: a [61]
avrdude: Recv: i [69]
avrdude: Recv: l [6c]
avrdude: Recv: . [0a]
avrdude: Recv:
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
So, I'm on the right port, with the right MCU...
What can I do more ?
