Welcome! Log In Create A New Profile

Plastic Extruder Working Group

Plastic Extruders, mostly - > http://objects.reprap.org/wiki/Extruder

Page 12 of 21 Pages:

10 111213 14

Forum List New Topic RSS

	Views	Posts	Last Post
How to make UV coating for headlight lenses? by cvpelayo	1,549	1	06/11/2011 06:03PM Last Post by cvpelayo
Standard Interface for Extruders by jcabrer	1,473	21	06/01/2011 07:27PM Last Post by BodgeIt
I have some thoughts here... by anton zedd	1,059	3	05/31/2011 09:55AM Last Post by Buback
Pre-made nozzles by Sublime	6,648	15	05/28/2011 07:17PM Last Post by NoobMan
How do I attach a hot end to Wades extruder? by Flackster	2,570	8	05/27/2011 02:01PM Last Post by jcabrer
Hobbed stepper shaft filament drive by billyzelsnack	1,364	3	05/26/2011 02:25AM Last Post by Stoffel15
Extruding - Non-sticking PLA- a bundle of questions by Flackster	2,792	5	05/24/2011 08:28AM Last Post by jcabrer
Extruder tip size and bore size by HereinCS	1,262	2	05/19/2011 03:03PM Last Post by CdnReprap
Aerogel insulation by Buback	3,614	9	05/09/2011 07:59AM Last Post by inh
Success Reports - Emergency Tape and Resistors by jcabrer	1,183	1	05/01/2011 11:27PM Last Post by jcabrer
OKKA power extruder rs (rock solid) by OKKA	1,741	1	04/27/2011 06:03PM Last Post by OKKA
using hydrolics to drive extruder? by Buback	1,032	3	04/27/2011 05:15PM Last Post by Buback
$30 plastic welder? by JohnWasser	7,039	11	04/26/2011 07:36PM Last Post by aka47
Brake line hotend by billyzelsnack	1,106	1	04/25/2011 11:40AM Last Post by billyzelsnack
Ultimaker 12v Cartridge Heater by Andrew Diehl	4,473	20	04/19/2011 08:37AM Last Post by BodgeIt
Pictures for the extruder wiki by Nudel	2,380	6	04/17/2011 04:28AM Last Post by SebastienBailard
PLA extruding problem by Ecir Hana	1,377	7	04/17/2011 03:11AM Last Post by Matthieu
Why use springs on the extruder? by Andrew Diehl	1,222	3	04/04/2011 05:04AM Last Post by AgeingHippy
Push-fit Hot-end for 1.75mm Filament (Bowden Extruder) by richrap	2,517	5	03/21/2011 05:56PM Last Post by richrap
Bowden Extruder with push-fit Pneumatic connectors by richrap	2,106	3	03/21/2011 05:28AM Last Post by richrap
Anyone used a ring heater? by HereinCS	1,260	7	03/19/2011 04:55AM Last Post by nophead
Screw drive to push filament? by patbob	1,575	6	03/16/2011 07:14PM Last Post by nophead
Sticky Message out of date? --^ by unicoder	1,113	6	03/16/2011 11:53AM Last Post by unicoder
Remote Motor Extruder (Shaft Transmission) by andysuth	3,004	28	03/10/2011 09:00PM Last Post by patbob
Print raft only? by boarboar	924	2	03/06/2011 12:56PM Last Post by NewPerfection
low-temp metal casting by VDX	4,987	8	03/04/2011 09:40PM Last Post by Cefiar
Grounding the hot end by Buback	1,072	5	02/25/2011 04:00AM Last Post by nophead
bowden-esque granular extruder? by Parker	1,921	14	02/24/2011 06:56PM Last Post by AgeingHippy
UV cure products for cars? by dlakin	1,006	2	02/23/2011 06:51PM Last Post by SebastienBailard
Extruder nozzle heater - possible ‘alternative’ approach? by NumberSix	3,687	2	02/18/2011 03:16AM Last Post by VDX

Page 12 of 21 Pages:

10 111213 14