Welcome! Log In Create A New Profile

Duet

Duet is the Arduino Due Compatible RepRap Electronics

Page 9 of 25 Pages:

7 8910 11

Forum List New Topic RSS

	Views	Posts	Last Post
Extruder motor going both forward and backwards on extrude by ElmoC	1,373	5	06/04/2017 08:39AM Last Post by ElmoC
Storing Calibration? by clearlynotstefan	638	2	06/03/2017 03:50AM Last Post by dc42
Firmware 1.18.1 and Heater Faults by DRTak	4,716	12	06/02/2017 01:23PM Last Post by dc42
Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC by Italia			This topic has been moved.
Duet Wifi, two drivers for one 8 wire motor? by M;kko	511	2	05/29/2017 02:20AM Last Post by dc42
Mechanical switch for z probe by chris33	1,316	10	05/25/2017 05:19PM Last Post by chris33
M997 S2 by 3D-Print	694	2	05/24/2017 02:26AM Last Post by dc42
M572 pressure advance for Diamond hotend? by o_lampe	644	5	05/23/2017 06:17AM Last Post by dc42
Fan selection? by clearlynotstefan	1,160	4	05/23/2017 02:18AM Last Post by drmaestro
PanelDue STOP not the same as DWC Emergency Stop? by PDBeal	547	3	05/22/2017 04:12PM Last Post by dc42
Firmware upgrade by joestefano	694	9	05/17/2017 04:18AM Last Post by dougal1957
Fan short! by clearlynotstefan	539	6	05/14/2017 01:33AM Last Post by clearlynotstefan
Raspberry Pi as display by Napalm1432	1,186	7	05/12/2017 02:26AM Last Post by o_lampe
just a quick connector question by chris33	580	3	05/07/2017 04:21PM Last Post by dc42
(small) Feature request by unromeo21	614	20	05/07/2017 08:06AM Last Post by roboprint
Duet 0.6 Burnt EO Heater Ground Now No Web Control Access by DRTak	605	5	05/05/2017 11:47PM Last Post by DRTak
Suggested Mosfet for Duet 0.8.5 by Nylkos	1,267	2	05/02/2017 05:11PM Last Post by dc42
DUET with IR sensor by selva_tvi	1,147	4	05/02/2017 05:00PM Last Post by dc42
Panel Due brightness control by JuJuDelta	648	5	04/30/2017 01:29PM Last Post by JuJuDelta
Probe triggered and don't stop by DeathmannX	1,548	7	04/27/2017 12:35PM Last Post by ElmoC
S3D skirt/brim with M572 active by unromeo21	586	1	04/25/2017 03:37PM Last Post by unromeo21
Different motor temperatures in serial connection by drmaestro	459	4	04/25/2017 03:03AM Last Post by dc42
Dual extrusion with Single extruder by selva_tvi	791	3	04/24/2017 01:46AM Last Post by selva_tvi
Edit heightmap.csv? [Bug?] by o_lampe	1,579	6	04/23/2017 03:40PM Last Post by dc42
Upgrading to PT100 by drmaestro	637	4	04/23/2017 03:31PM Last Post by dc42
Power failure, Print pause - Resume by selva_tvi	2,307	6	04/23/2017 05:02AM Last Post by dc42
Duet stopped mid print, doesn'T work anymore..... by drmaestro	968	10	04/21/2017 05:08PM Last Post by dc42
Question for DC42 by lolocaledo	717	8	04/21/2017 04:59PM Last Post by dc42
external sd/usb slot by Napalm1432	491	4	04/21/2017 04:57PM Last Post by dc42
Setting Z offset for printing by drmaestro	18,522	7	04/17/2017 02:58PM Last Post by dc42

Page 9 of 25 Pages:

7 8910 11