Welcome! Log In Create A New Profile

Duet

Duet is the Arduino Due Compatible RepRap Electronics

Page 6 of 25 Pages:

4 567 8

Forum List New Topic RSS

	Views	Posts	Last Post
Will the SmartEffector solve all (many?) (some?) of my problems by Karatektus	742	4	03/09/2018 07:49AM Last Post by dc42
About to order some Duet items - raising a question by Koenig	636	4	03/04/2018 12:24PM Last Post by dc42
Ethernet troubles with 0.6 and firmware 1.20 by maso	683	4	02/27/2018 03:56PM Last Post by dc42
bed dimension calibration. by JustSumGuy	1,164	3	02/26/2018 02:39PM Last Post by JustSumGuy
SD Card Structure 3DP Micro by Bill Clark	843	1	02/25/2018 09:31PM Last Post by Bill Clark
Strange steps per mm to rounds per minute conversion by DrPFF	930	12	02/25/2018 03:58AM Last Post by o_lampe
Duet Ethernet - Dual Extruders - Macros/Switching Extruders by blandified	1,258	13	02/24/2018 05:38PM Last Post by dc42
Controlling two DuetWifi ? by o_lampe	584	7	02/21/2018 04:07AM Last Post by dc42
connecting to wifi problem by JustSumGuy	1,591	4	02/19/2018 12:57PM Last Post by JustSumGuy
5v inductive sensor to Duet Wifi by JustSumGuy	3,627	7	02/13/2018 01:11PM Last Post by JustSumGuy
Problem with BLTouch after upgrading to Firmware 1.20 by drmaestro	1,252	2	02/10/2018 04:03PM Last Post by dc42
DUET 0.6 heat bed power not working by selva_tvi	648	4	02/08/2018 11:38AM Last Post by JustSumGuy
DuetWifi Paneldue Heater Issue by gadittri	1,075	6	02/03/2018 03:45PM Last Post by dc42
Duet WiFi temperatures are too low. by Treito	2,079	5	01/28/2018 08:58AM Last Post by dc42
basic protocol for using baby-stepping? by shadowphile	626	3	01/28/2018 05:19AM Last Post by shadowphile
print froze halfway up by shadowphile	543	7	01/28/2018 03:18AM Last Post by dc42
Duet WiFi - problems with interpolation. by Treito	916	1	01/21/2018 05:51AM Last Post by Treito
firmware upgrade latest version by JustSumGuy	1,038	5	01/10/2018 04:49PM Last Post by JustSumGuy
G31 probe offset confusion by o_lampe	2,856	3	01/03/2018 11:56AM Last Post by o_lampe
"Attempting to extrude with no tool selected", and how to set up fans by Lobotomy	2,306	8	01/03/2018 03:44AM Last Post by o_lampe
My proximity sensor endstops not working by chichirod	1,594	7	12/31/2017 01:27PM Last Post by dc42
Duet 0.6 Bed temperature is too low. by Treito	752	10	12/29/2017 05:10AM Last Post by Treito
Crunchy X-axis on Duet Wifi by cheeseandham	1,117	4	12/22/2017 05:34PM Last Post by dc42
controlled heated box by JustSumGuy	723	7	12/20/2017 04:35PM Last Post by JustSumGuy
Repair a Duet 0.85 a "little bit" hot ? by Crixos	604	6	12/19/2017 09:06AM Last Post by dc42
My endstops do not work? (RADDS + Kossel Delta) by Lobotomy	1,006	7	12/19/2017 03:19AM Last Post by o_lampe
RepRapFirmware 1.20 RC2 now available by dc42	720	2	12/14/2017 11:31AM Last Post by JustSumGuy
Extruder skipping steps? by Kevin37	2,496	26	12/12/2017 10:23AM Last Post by Kevin37
Bed Mesh by jbolt	853	4	12/12/2017 03:12AM Last Post by o_lampe
Turning OFF & ON the DuetWiFi with a relay by Dunston-UK	2,059	3	12/08/2017 01:56PM Last Post by Dunston-UK

Page 6 of 25 Pages:

4 567 8