Welcome! Log In Create A New Profile



Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post

Minor feature request

by av8r1
209 7 04/07/2017 03:38PM
Last Post by av8r1

No web interface after upgrade from 1.16 to 1.18RC1

by unromeo21
325 19 04/07/2017 12:41PM
Last Post by unromeo21

First Layer Too High

by ElmoC
255 11 04/06/2017 03:27PM
Last Post by ElmoC

hotend and bed stops heating

by lolocaledo
177 8 04/04/2017 11:35AM
Last Post by dc42

Duet vs Duet WiFi

by leadinglights
307 2 03/31/2017 01:12PM
Last Post by dc42

G29 S1 compensates only for Y lower than 100

by unromeo21
128 3 03/31/2017 11:38AM
Last Post by unromeo21

New RepRapFirmware 1.18RC1

by dc42
265 1 03/28/2017 11:58AM
Last Post by dc42

Strange behavior with Delta

by lolocaledo
153 2 03/27/2017 08:37AM
Last Post by dougal1957

Duet & SSR

by Nylkos
339 3 03/23/2017 06:13PM
Last Post by IMBoring25

Tool 0 not driven because of a heater fault

by Northspire
227 9 03/23/2017 03:29AM
Last Post by Northspire

Connecting servo

by fma
168 5 03/23/2017 01:32AM
Last Post by fma

Cant connect to Web Interface on Mac

by InventEd
219 9 03/19/2017 04:49AM
Last Post by InventEd

DWC Backup System Files After Edit

by ElmoC
154 1 03/18/2017 09:10AM
Last Post by ElmoC

Duet custom axes and leveling

by Napalm1432
195 3 03/16/2017 02:52AM
Last Post by o_lampe

DuetWifi for Tronxy x3 Attachments

by snape666
324 5 03/15/2017 01:48AM
Last Post by snape666

Vagueness of G-Code Reference

by av8r1
226 19 03/13/2017 08:01PM
Last Post by av8r1

Just Updated from a very old firmware

by wayno complaino
147 6 03/13/2017 01:10PM
Last Post by Masterjuggler

Flyback diode for air pump control

by Teilchen
259 17 03/13/2017 08:43AM
Last Post by dc42

Measuring difference between IR probe and hotend

by ezwul
198 4 03/12/2017 03:28PM
Last Post by ezwul

FT5 extruder motor won't move

by brylandry
125 2 03/10/2017 11:41PM
Last Post by dc42

Inductive sensor temperature compensation.

by FrankPropaneTank
234 1 03/09/2017 04:56PM
Last Post by FrankPropaneTank

dc42 version - How to change lateral z-probe speeds?

by shadowphile
196 10 03/08/2017 01:57PM
Last Post by dc42

Corexy bed sensor concept. Possible?

by clearlynotstefan
248 9 03/03/2017 10:26AM
Last Post by dc42

Noob requiring assistance

by Nylkos
198 9 03/01/2017 12:20PM
Last Post by Nylkos

Need help with a Bondtech Extruder with duet 0.8.5 Attachments

by Northspire
227 12 02/27/2017 08:40PM
Last Post by Northspire

Finding Trigger Heights for Offsets

by Kurzaa
151 3 02/27/2017 06:58PM
Last Post by Kurzaa

Extruder offset

by joestefano
146 2 02/27/2017 12:02AM
Last Post by dc42

New edge firmware 1.18beta1

by dc42
389 6 02/24/2017 03:10AM
Last Post by heapstar


by joestefano
192 2 02/22/2017 11:03PM
Last Post by dc42

Bed preheat (M190) doesn't send updates via USB serial

by maso
173 10 02/22/2017 03:06PM
Last Post by maso