Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post

Duet 0.6 Burnt EO Heater Ground Now No Web Control Access

by DRTak
163 5 05/05/2017 08:47PM
Last Post by DRTak

Suggested Mosfet for Duet 0.8.5

by Nylkos
213 2 05/02/2017 02:11PM
Last Post by dc42

DUET with IR sensor

by selva_tvi
225 4 05/02/2017 02:00PM
Last Post by dc42

Panel Due brightness control

by JuJuDelta
157 5 04/30/2017 10:29AM
Last Post by JuJuDelta

Probe triggered and don't stop

by DeathmannX
180 7 04/27/2017 09:35AM
Last Post by ElmoC

S3D skirt/brim with M572 active

by unromeo21
180 1 04/25/2017 12:37PM
Last Post by unromeo21

Different motor temperatures in serial connection

by drmaestro
149 4 04/25/2017 12:03AM
Last Post by dc42

Dual extrusion with Single extruder

by selva_tvi
188 3 04/23/2017 10:46PM
Last Post by selva_tvi

Edit heightmap.csv? [Bug?]

by o_lampe
181 6 04/23/2017 12:40PM
Last Post by dc42

Upgrading to PT100

by drmaestro
179 4 04/23/2017 12:31PM
Last Post by dc42

Power failure, Print pause - Resume

by selva_tvi
254 6 04/23/2017 02:02AM
Last Post by dc42

Duet stopped mid print, doesn'T work anymore..... sad smiley

by drmaestro
224 10 04/21/2017 02:08PM
Last Post by dc42

Question for DC42

by lolocaledo
238 8 04/21/2017 01:59PM
Last Post by dc42

external sd/usb slot

by Napalm1432
139 4 04/21/2017 01:57PM
Last Post by dc42

Setting Z offset for printing

by drmaestro
1,385 7 04/17/2017 11:58AM
Last Post by dc42

Duet Ethernet available

by dc42
385 5 04/15/2017 03:10AM
Last Post by dc42

Wiring a resistor in parallel

by drmaestro
167 1 04/15/2017 12:27AM
Last Post by drmaestro

Z motor delta question

by clearlynotstefan
172 5 04/13/2017 03:07AM
Last Post by dc42

External trigger from endstop pins E2,3,4...

by maczar
124 4 04/11/2017 06:48AM
Last Post by dc42

Minor feature request

by av8r1
194 7 04/07/2017 03:38PM
Last Post by av8r1

No web interface after upgrade from 1.16 to 1.18RC1

by unromeo21
308 19 04/07/2017 12:41PM
Last Post by unromeo21

First Layer Too High

by ElmoC
229 11 04/06/2017 03:27PM
Last Post by ElmoC

hotend and bed stops heating

by lolocaledo
161 8 04/04/2017 11:35AM
Last Post by dc42

Duet vs Duet WiFi

by leadinglights
262 2 03/31/2017 01:12PM
Last Post by dc42

G29 S1 compensates only for Y lower than 100

by unromeo21
119 3 03/31/2017 11:38AM
Last Post by unromeo21

New RepRapFirmware 1.18RC1

by dc42
246 1 03/28/2017 11:58AM
Last Post by dc42

Strange behavior with Delta

by lolocaledo
140 2 03/27/2017 08:37AM
Last Post by dougal1957

Duet & SSR

by Nylkos
307 3 03/23/2017 06:13PM
Last Post by IMBoring25

Tool 0 not driven because of a heater fault

by Northspire
185 9 03/23/2017 03:29AM
Last Post by Northspire

Connecting servo

by fma
143 5 03/23/2017 01:32AM
Last Post by fma