Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post

Duetwifi and Diamond hotend on Delta

by hvashist
161 2 06/28/2017 12:08AM
Last Post by o_lampe

M584 driver mapping ignores different steps/mm

by o_lampe
115 3 06/23/2017 06:52AM
Last Post by o_lampe

Hot End Heating Up When Power Turned On Attachments

by Kurzaa
283 6 06/21/2017 11:41PM
Last Post by dc42

Which IP Cam?

by DeltaCon
195 2 06/20/2017 03:27PM
Last Post by dc42

Fan voltage

by fma
145 5 06/20/2017 03:20AM
Last Post by fma

Support for mixing extruders

by fma
144 2 06/20/2017 02:48AM
Last Post by dc42

Intermittend stepper hickup after cold start

by o_lampe
128 3 06/13/2017 10:34PM
Last Post by o_lampe

Doing action when changing status

by maczar
123 2 06/12/2017 11:14PM
Last Post by dc42

Hot end crashes into second layer

by alangibson
192 6 06/12/2017 06:43AM
Last Post by DeltaCon

(ignore) PC not connecting to new Duet-Ethernet board (windows)

by shadowphile
476 1 06/11/2017 03:33PM
Last Post by shadowphile

4 axis polar geometry

by fma
147 8 06/09/2017 11:29AM
Last Post by fma

Web interface

by fma
163 3 06/09/2017 05:01AM
Last Post by fma

Mixing cartesian and CoreXY config?

by o_lampe
197 14 06/08/2017 04:39AM
Last Post by dc42

Connecting your Duet 0.85 Straight to Computers Ethernet

by chris33
154 2 06/07/2017 02:37PM
Last Post by dc42

RepRapFirmware 1.18 and Panel Due firmware 1.16 released   (Pages: 1 2)

by dc42
973 34 06/06/2017 02:09PM
Last Post by dc42

Extruder motor going both forward and backwards on extrude

by ElmoC
143 5 06/04/2017 05:39AM
Last Post by ElmoC

Storing Calibration?

by clearlynotstefan
163 2 06/03/2017 12:50AM
Last Post by dc42

Firmware 1.18.1 and Heater Faults

by DRTak
360 12 06/02/2017 10:23AM
Last Post by dc42
This topic has been moved.

Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC

by Italia
    This topic has been moved.

Duet Wifi, two drivers for one 8 wire motor?

by M;kko
166 2 05/28/2017 11:20PM
Last Post by dc42

Mechanical switch for z probe

by chris33
230 10 05/25/2017 02:19PM
Last Post by chris33

M997 S2

by 3D-Print
158 2 05/23/2017 11:26PM
Last Post by dc42

M572 pressure advance for Diamond hotend?

by o_lampe
142 5 05/23/2017 03:17AM
Last Post by dc42

Fan selection?

by clearlynotstefan
169 4 05/22/2017 11:18PM
Last Post by drmaestro

PanelDue STOP not the same as DWC Emergency Stop?

by PDBeal
119 3 05/22/2017 01:12PM
Last Post by dc42

Firmware upgrade

by joestefano
263 9 05/17/2017 01:18AM
Last Post by dougal1957

Fan short!

by clearlynotstefan
180 6 05/13/2017 10:33PM
Last Post by clearlynotstefan

Raspberry Pi as display

by Napalm1432
306 7 05/11/2017 11:26PM
Last Post by o_lampe

just a quick connector question

by chris33
172 3 05/07/2017 01:21PM
Last Post by dc42

(small) Feature request

by unromeo21
213 20 05/07/2017 05:06AM
Last Post by roboprint