Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post
Sticky

Where to get help for the Duet series of 3D printer electronics

by dc42
1,144 5 12/23/2016 12:22PM
Last Post by PDBeal

Replikeo offloading Duet 0.6 boards at $19

by dc42
136 3 09/17/2017 11:47PM
Last Post by dc42

Duet 0.85 Thermocouple ?

by Gaou
56 2 09/16/2017 02:24PM
Last Post by dc42

Octopi with duet 0.8.5 usb   (Pages: 1 2)

by Napalm1432
252 33 09/11/2017 12:05PM
Last Post by nique911

DWC not updating - uploaded 1.19 and it still shows version 1.11 after refreshing page?

by Bob64
93 8 09/06/2017 06:11PM
Last Post by Bob64

Does the Duet support Gowoops 3D Printer Controller LCD?

by dmiles
338 10 09/06/2017 01:49PM
Last Post by rstepanov

Crazy Idea - Duplicate motors?

by clearlynotstefan
125 14 09/06/2017 12:47AM
Last Post by kasom

mini height sensor triggering

by Gaou
92 7 09/03/2017 12:21PM
Last Post by Raetron

Help with electronic/electric setup

by Otura
91 9 09/01/2017 07:11AM
Last Post by dc42

SMART RAMPS For Due

by cxandy
623 4 08/30/2017 01:29PM
Last Post by boelle

Heightmap to the moon... Attachments

by DeltaCon
357 28 08/25/2017 01:33PM
Last Post by dc42

Problems with autotuning hot end after upgrade to 1.19

by David J
71 3 08/22/2017 04:19AM
Last Post by David J

Release notes for v1.19? {NOW SORTED]

by David J
138 6 08/22/2017 02:53AM
Last Post by David J

New Duet 0.85, windows makes disconnect sound constantly

by scottybfg
127 5 08/15/2017 06:45PM
Last Post by scottybfg

Urgent help - Mini IR sensor with DUET 0.6 Attachments

by selva_tvi
165 5 08/15/2017 05:09PM
Last Post by dc42

Futuristic FDM idea

by clearlynotstefan
188 3 08/03/2017 01:58PM
Last Post by trevmas

Ultratronics V1.0 & RepRapDiscount Full Graphic LCD

by TheHackerArtist
115 3 08/03/2017 12:17PM
Last Post by TheHackerArtist

Filament detection and user pause button Attachments

by PRZ
489 5 08/02/2017 12:04PM
Last Post by dc42

Chamber Heater Control?

by clearlynotstefan
126 2 07/12/2017 07:38AM
Last Post by dc42

Duet Ethernet Hotend Fan Turns Off and On during print and clogs nozzle

by DRTak
119 6 07/07/2017 08:36AM
Last Post by DRTak

Duex2 to Duex5 upgrade

by fma
114 6 07/05/2017 11:01AM
Last Post by dc42

Working with two bed sizes ?

by unromeo21
99 2 07/05/2017 04:08AM
Last Post by dc42

Bed connector burnt - DUET 0.6 Attachments

by selva_tvi
127 5 07/02/2017 12:58AM
Last Post by selva_tvi

Please help: Ormerod 1 its been a while!! What do I need.

by gregstah
166 7 06/29/2017 06:06AM
Last Post by Karoo Klong

Duetwifi and Diamond hotend on Delta

by hvashist
147 2 06/28/2017 12:08AM
Last Post by o_lampe

M584 driver mapping ignores different steps/mm

by o_lampe
103 3 06/23/2017 06:52AM
Last Post by o_lampe

Hot End Heating Up When Power Turned On Attachments

by Kurzaa
271 6 06/21/2017 11:41PM
Last Post by dc42

Which IP Cam?

by DeltaCon
173 2 06/20/2017 03:27PM
Last Post by dc42

Fan voltage

by fma
133 5 06/20/2017 03:20AM
Last Post by fma

Support for mixing extruders

by fma
135 2 06/20/2017 02:48AM
Last Post by dc42

Intermittend stepper hickup after cold start

by o_lampe
122 3 06/13/2017 10:34PM
Last Post by o_lampe