Welcome! Log In Create A New Profile

Advanced

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Subject Views Posts Last Post

Strange timings in source code

by ArtemKuchin
104 3 02/26/2017 12:03PM
Last Post by ArtemKuchin

connecting second z-stepper-motor Attachments

by XiniX
106 4 02/26/2017 12:03AM
Last Post by o_lampe

Issues with y direction in corexy

by someoneonly
268 10 02/25/2017 04:54AM
Last Post by someoneonly

Marlin firmware, ATMEGA2560 port mappings?

by zapro
145 2 02/24/2017 04:04PM
Last Post by Roxy

Mendel Tricolour master board firmware help please

by wedgehead72
108 2 02/24/2017 01:38PM
Last Post by wedgehead72

Jennyprinter 3 , which firmware is correct? Attachments

by Micstar
223 1 02/24/2017 02:00AM
Last Post by Micstar

Z probe repeatability - no data

by Scott1326
240 9 02/23/2017 11:19PM
Last Post by Scott1326

(RAMPS)Hotend change pin from D8 to D10

by SporyPing
282 6 02/21/2017 12:52PM
Last Post by Dust

There maybe a problem for ST7920 initial in ultralcd_st7920_u8glib_rrd.h

by Chincheng
109 1 02/17/2017 01:16AM
Last Post by Chincheng

custom menu options with multiple lines of G-Code

by av8r1
136 3 02/16/2017 07:38AM
Last Post by av8r1

G code for calibration

by DOYT
170 8 02/16/2017 06:51AM
Last Post by o_lampe

Bed Levelling on RC8 working but not compensating

by pcsentinel2
189 12 02/13/2017 12:36PM
Last Post by pcsentinel2

Adjusting Marlin for quite printing

by DOYT
126 6 02/12/2017 10:32PM
Last Post by DOYT

Bitte um Hilfe! Fehler beim kompilieren Marlin RC8

by 3D Horst
114 1 02/11/2017 11:00AM
Last Post by 3D Horst

Full Graphics display on Megatronics v3.1

by Outbound
134 3 02/10/2017 03:30AM
Last Post by Outbound

Marlin 1.1 RC8 reboots after bed reaches temps

by JustinTimeToo
180 8 02/09/2017 10:06AM
Last Post by JustinTimeToo

X and Y axis skips forward before auto bed leveling.?!

by Draytology
78 3 02/09/2017 02:04AM
Last Post by mjoyce

Looking for some help understand a ZMIN ENDSTOP issue.

by mjoyce
110 3 02/08/2017 12:15PM
Last Post by mjoyce

When is it necessary to setup multiple "E0 E1 E2" steps and what is the format?

by kd6hq
282 20 02/07/2017 12:30PM
Last Post by kd6hq

Problema con Kossel mini

by marco.ierimonte
115 1 02/04/2017 04:24AM
Last Post by marco.ierimonte

Sending on Serial pins other than Serial0

by mamech
120 5 02/04/2017 02:20AM
Last Post by mamech

Setting Z axis speed

by DOYT
443 16 02/03/2017 10:44AM
Last Post by Floyd

Z Axis issues after leadscrew conversion

by franklectic1
138 6 02/02/2017 08:16PM
Last Post by franklectic1

Auto Leveling Z homing position and extruder distance?

by mcm001
132 2 02/01/2017 07:56AM
Last Post by Roxy

Error uploading new Marlin

by akcasper
179 8 01/30/2017 01:36PM
Last Post by Roxy

Tower Angular Corrections

by Jiehfeng
258 1 01/30/2017 08:49AM
Last Post by Jiehfeng

Setting Marlin for LCD problem Attachments

by DOYT
510 21 01/30/2017 08:10AM
Last Post by Roxy

Auto Bed Leveling RC8 - Z axis goes up while homing

by h4nc
204 3 01/25/2017 05:26AM
Last Post by h4nc

Question about using marlin in laser cutting applications

by mamech
143 6 01/25/2017 04:40AM
Last Post by mamech

true bed levelling - not bed level compensation - Does this already exist?

by Swift
160 3 01/24/2017 01:48AM
Last Post by DeuxVis