Welcome! Log In Create A New Profile

Advanced

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Subject Views Posts Last Post

"bugfix-1.1.x" and "Viki2" not working Attachments

by iamturbo1978
77 1 12/06/2017 06:01AM
Last Post by iamturbo1978

Display problem on reprapdiscount full graphic smart controller display.

by hardy8
134 4 12/05/2017 10:14AM
Last Post by hardy8

Need help with FW upgrade of Dual X Carriage, Dual Z

by mic03167
125 2 12/05/2017 06:19AM
Last Post by mic03167

Problem flashing Marlin onto Melzi board.

by Billythakid
230 1 12/03/2017 11:17AM
Last Post by Billythakid

Non-marlin to marlin upgrade, help needed

by BaronPork
146 5 12/02/2017 11:34AM
Last Post by Roxy

zprobe loses autolevel

by ProSoft
129 5 12/01/2017 09:45AM
Last Post by ProSoft

2 axis, 3 drivers

by okuzster
115 3 12/01/2017 01:18AM
Last Post by eugen360

Marlin Configuration Attachments

by hooogle
341 6 11/30/2017 09:41PM
Last Post by Dust

M600 beep

by Floyd
94 3 11/30/2017 06:33PM
Last Post by Floyd

Marlin auto bed leveling help

by eddy99
176 3 11/30/2017 03:33PM
Last Post by eddy99

Marlin Cold Extrude

by hooogle
108 3 11/29/2017 08:25PM
Last Post by hooogle

Marlin 1.1.6 z-probe connected to Z-MAX as endstop not working Attachments

by wormie_dk
142 4 11/29/2017 09:51AM
Last Post by wormie_dk

LCD Encoder setup

by bhbloom
106 1 11/28/2017 03:14AM
Last Post by bhbloom

Unable to print in bed centre

by noelmm
129 5 11/27/2017 11:47PM
Last Post by noelmm

Need some Firmware Mods... Who wanna get paid to do it for me???

by WatIDo
166 7 11/27/2017 08:26PM
Last Post by WatIDo

Marlin 4.3 ERR MIN TEMP BED

by pcasini
109 7 11/27/2017 10:24AM
Last Post by pcasini

Wont use ABL measured values Attachments

by ManuelW
91 2 11/27/2017 03:04AM
Last Post by ManuelW

Laser mode

by rfresh737
132 1 11/22/2017 09:10PM
Last Post by rfresh737

Compiler Error Attachments

by Chips
316 12 11/22/2017 07:53PM
Last Post by Roxy

Dual Y axis motors required, E1/E0 or Z pins?

by dutchbarracuda
111 3 11/21/2017 07:38AM
Last Post by dutchbarracuda

Receive OK Message only when Movement is complete

by Shishir
106 2 11/16/2017 06:13PM
Last Post by Dust

Advice on start and end G-code.

by kd6hq
163 3 11/16/2017 01:02PM
Last Post by kd6hq

Triple Z-drive with Stepper Expander

by E_tech_14
164 3 11/15/2017 12:14AM
Last Post by E_tech_14

M600 question

by kd6hq
208 13 11/14/2017 04:59PM
Last Post by kd6hq

Z axis Homing Issue

by Brass-51
263 11 11/10/2017 03:49PM
Last Post by Roberts_Clif

Marlin configurator

by Jes
1,797 11 11/09/2017 05:27AM
Last Post by Jes

Error message: "Marlin\SanityCheck.h:1325:1: error:

by kd6hq
184 4 11/08/2017 07:32AM
Last Post by kd6hq

HELP! Endstop problem in Marlin Attachments

by airwolf99
281 9 11/07/2017 08:02PM
Last Post by airwolf99

New algorithm

by scallas
138 2 11/07/2017 12:30AM
Last Post by Dust
This topic has been moved.

Repairing a Printrboard potentiometer

by hussainsail2002
    This topic has been moved.