Welcome! Log In Create A New Profile


Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Subject Views Posts Last Post

Temps reading high, using AD595 with Thermocouples Attachments

by ricknsharon
24 4 03/22/2018 05:45PM
Last Post by Roberts_Clif

Only some endstops function Attachments

by ricknsharon
42 3 03/22/2018 09:09AM
Last Post by ricknsharon

PID Weirdness Attachments

by DaHai8
73 4 03/22/2018 12:00AM
Last Post by DaHai8

Homing offsets

by MarinusK
40 1 03/21/2018 03:09AM
Last Post by MarinusK

Z_Probe working strategy

by Mohan Muthusamy
121 3 03/20/2018 07:14AM
Last Post by Roxy

Is M915 / TMC_Z_CALIBRATION with TMC 2130 useful?

by tbeaulieu
38 2 03/20/2018 07:11AM
Last Post by Roxy

Cooling the bed at the end of a print automatically.

by isolt
38 1 03/19/2018 05:56PM
Last Post by isolt

Marlin 1.1.8 and my CR10s It aint liking it!

by cyborblades
141 6 03/19/2018 09:07AM
Last Post by cyborblades

Auto calibration points

by robingantois
46 1 03/18/2018 08:38AM
Last Post by robingantois

Problem with LCD on Mini-Rambo Attachments

by dpalo
48 2 03/18/2018 08:06AM
Last Post by obewan

Multi-Stepping in Marlin

by RishabhX3576
64 3 03/17/2018 08:23PM
Last Post by RishabhX3576

Need Help With BL Touch

by 3DNublet
50 2 03/17/2018 06:55PM
Last Post by 3DNublet

Mightyboard 2004 LCD with Marlin?

by villamany
78 2 03/16/2018 05:29AM
Last Post by Dust

Octoprint & EEPROM CRC checksum Errors

by sinned
64 2 03/15/2018 08:26PM
Last Post by Roxy

Need Help Configuring EndStops

by 3DNublet
133 14 03/15/2018 08:19AM
Last Post by 3DNublet

(bugfix-2.0.x) SD card print stopped -> BIG hole in bed

by kubik256
64 1 03/15/2018 06:24AM
Last Post by kubik256

Calibrating steps per mm/in on A,B,C steppers on a delta

by jemenake
43 3 03/14/2018 09:02PM
Last Post by jemenake

UBL and Z-Offset: Manual probing of points where probe can't reach

by LichtiMC
75 4 03/12/2018 05:56PM
Last Post by Roxy

Possible to Change Message "E1 heating..."?

by 3DStyle
69 2 03/12/2018 02:24PM
Last Post by 3DStyle

Possible to Change Message "E1 heating..."?

by 3DStyle
63 1 03/12/2018 02:23PM
Last Post by 3DStyle

Marlin 2.0 and Smoothie

by StlLooking
291 4 03/12/2018 11:04AM
Last Post by Techgirl

[1.1.8] G26 Pattern didn't finish and then lowerd the Z axis

by Gazit6
53 2 03/11/2018 04:48PM
Last Post by Roxy

Cannot upload Tronxy X3A Firmware but repetiermoody smiley

by Tunderprint1000
95 4 03/08/2018 11:08PM
Last Post by Tunderprint1000

Does marlin BEEP when 3d print is done ?

by windchime
116 6 03/08/2018 10:21PM
Last Post by Melty

Problem with OLED (LCD) 2004 with HDD44780 controller

by Nitec0re
61 1 03/08/2018 03:25PM
Last Post by Nitec0re

Circular moves slows down as I increase print speed.

by j0achim
63 1 03/08/2018 02:08PM
Last Post by j0achim

Marlin 1.1.8+ M420 S1 required after G28

by DaHai8
167 5 03/08/2018 11:15AM
Last Post by ruggb

Inductive auto level Marlin1.1.8

by jaded
145 6 03/08/2018 05:52AM
Last Post by ruggb

Calculating Steps/mm

by 3DNublet
86 5 03/07/2018 02:57PM
Last Post by 3DNublet

Delta: Determine delta-radius, bed tilt, and bed imperfections all with one test?

by jemenake
51 2 03/07/2018 01:05PM
Last Post by jemenake