Welcome! Log In Create A New Profile

Advanced

Fisher

... it's a small Delta printer from RepRapPro 
Page 4 of 10    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

My Fisher experience (so far..) and advice for anyone about to build one Attachments

by Geoffro 		1,498 8 03/16/2016 10:50AM
Last Post by janpenguin

How to insert new roll of filament while in printing?

by janpenguin 		696 2 03/12/2016 02:20AM
Last Post by bgkdavis

Octoprint?

by upsch2000 		797 2 03/11/2016 04:36PM
Last Post by dc42

Needing spare parts (printed)

by FragrantParrot 		656 3 03/10/2016 07:36PM
Last Post by FragrantParrot

Fisher Minimum Wall Thickness

by geeksarebeta 		718 3 03/07/2016 04:03AM
Last Post by geeksarebeta

Panel designs optimized for metal Attachments

by StupendousMan 		846 13 03/03/2016 05:11AM
Last Post by StupendousMan

U.S. Fisher distributor?

by BioLumo 		697 2 02/28/2016 07:57AM
Last Post by StupendousMan

Bushing Instead of Bearings?

by DADIY 		745 2 02/24/2016 10:48AM
Last Post by StupendousMan

Hot End Blocked?

by geeksarebeta 		741 3 02/14/2016 03:41PM
Last Post by PRZ

Mistacke with Duet Web Control 1.08 and RepRapFirmware 1.09r-ch

by Anubis_Juventino 		800 5 02/13/2016 05:07AM
Last Post by Anubis_Juventino

Dead fan?

by ntsewell 		738 7 02/10/2016 12:16PM
Last Post by DADIY

Hot end not cooling enough?

by ByteSlinger 		758 3 02/08/2016 10:45AM
Last Post by Martoh

Looking to build up a kit of spares...

by lord_alan 		769 3 02/08/2016 07:37AM
Last Post by StupendousMan

Config.g for Firmware 1.09r

by ByteSlinger 		800 3 02/07/2016 06:34PM
Last Post by ByteSlinger

Fisher printing of 3DBenchy Attachments

by tblitzy 		1,626 20 02/01/2016 10:48AM
Last Post by JamesK

Meet the Fisher XT Attachments

by DADIY 		1,105 11 02/01/2016 03:58AM
Last Post by DADIY

Idler Lever not holding tension

by ByteSlinger 		690 3 01/31/2016 09:31PM
Last Post by PRZ

RepRapPro closed down, but need a rod

by ronnietucker 		1,075 11 01/29/2016 07:35AM
Last Post by jmgiacalone

Wood and Bronze Filament

by ByteSlinger 		791 6 01/29/2016 03:30AM
Last Post by DADIY

problem with fisher 1

by Anubis_Juventino 		790 4 01/26/2016 06:32PM
Last Post by bgkdavis

Logo STL

by ByteSlinger 		874 3 01/23/2016 08:50AM
Last Post by reprapprochina

Carbon Arms Attachments   (Pages: 1 2)

by bgkdavis 		2,848 36 01/21/2016 07:04PM
Last Post by bgkdavis

Homing finishes 14mm above print bed...

by ByteSlinger 		845 1 01/20/2016 06:31PM
Last Post by ByteSlinger

Can I make a Fisher without reprappro parts?

by StupendousMan 		1,010 6 01/18/2016 09:43PM
Last Post by bgkdavis

Simplify3D setup?   (Pages: 1 2)

by Theolodian 		4,594 57 01/18/2016 04:48PM
Last Post by jmg123

Hot end peaks at 145 then drops back down

by ByteSlinger 		682 2 01/18/2016 04:28PM
Last Post by dc42

Spare parts

by Thorn666 		893 14 01/18/2016 08:51AM
Last Post by DADIY

Getting low resistance on pre-powerup check

by ByteSlinger 		769 1 01/17/2016 06:52PM
Last Post by ByteSlinger

Calibration Speed.

by DADIY 		783 5 01/17/2016 12:10PM
Last Post by DADIY

Fisher Rod DXF download - [FOUND]

by ByteSlinger 		776 3 01/13/2016 09:43PM
Last Post by PRZ
Page 4 of 10    Pages: Previous12345NextLast