Welcome! Log In Create A New Profile

Fisher

... it's a small Delta printer from RepRapPro

Page 3 of 10 Pages:

1 234 5

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	[solved] What parts to print? by GRAYWOLF	960	9	06/29/2016 03:05PM Last Post by GRAYWOLF
	Printing problems [SOLVED] by Kalle	910	8	06/29/2016 02:54PM Last Post by Kalle
	Effector Mounting Alternatives by SEUTec	771	2	06/28/2016 02:27PM Last Post by Kalle
	Few questions from somebody clueless by Klebbin_Fisher	1,033	10	06/23/2016 04:24PM Last Post by hakimio
	Effector for E3D v6 by jmg123	2,411	13	06/13/2016 03:36PM Last Post by DADIY
	Unable to setup Fisher Delta - help? by AndyKay	1,234	3	06/05/2016 05:36AM Last Post by PRZ
	Weird setup issue by AndyKay	920	10	06/03/2016 06:15PM Last Post by bgkdavis
	Fisher Logo STL by SSMagic	738	3	05/31/2016 06:21PM Last Post by SSMagic
	Getting rid of my Fisher Delta by LocostJosh	993	1	05/31/2016 04:50PM Last Post by LocostJosh
	Updated firmware and now homing and bed levelling is broken by ByteSlinger	1,041	30	05/27/2016 03:17AM Last Post by DADIY
	Print bed levelling by FragrantParrot	2,426	10	05/19/2016 01:47AM Last Post by bgkdavis
	Extruder motor skipping steps by tml	7,995	10	05/16/2016 07:38AM Last Post by ByteSlinger
	Wanted: Fisher filament tensioner levers... by Sash	782	4	05/09/2016 06:48PM Last Post by bgkdavis
	Flexible PLA from RigidInk by ntsewell	1,818	10	04/29/2016 07:46AM Last Post by jmg123
	Anyway to Connect to more than one Fisher at once? by Geoffro	700	3	04/23/2016 09:54AM Last Post by Geoffro
	One wavy side - any ideas? by RoboticMonk3y	742	8	04/19/2016 08:24PM Last Post by janpenguin
	Cooling motors and board by ByteSlinger	717	4	04/18/2016 04:24AM Last Post by ByteSlinger
	New HXM printer with Fisher components by PRZ	1,216	7	04/07/2016 05:55PM Last Post by PRZ
	new effector and carraige (Pages: 1 2) by bgkdavis	2,017	48	04/07/2016 02:07PM Last Post by geeksarebeta
	Lighting setups by ByteSlinger	696	6	04/07/2016 04:28AM Last Post by SSMagic
	Lost network connection mid-print by ByteSlinger	674	4	04/06/2016 12:58PM Last Post by dc42
	Maintenance? by Theolodian	1,332	10	04/04/2016 09:12AM Last Post by SSMagic
	Extruder temperature after adding heated bed. by DADIY	715	5	03/31/2016 12:21PM Last Post by DADIY
	Carbon Arms (Again) (Pages: 1 2) by lord_alan	2,921	32	03/30/2016 05:52AM Last Post by Sean.kennedy
	Prints warping by pixelseventy2	795	5	03/27/2016 02:57PM Last Post by Wissing
	About USB connection by tavietbao	793	8	03/22/2016 03:25AM Last Post by tavietbao
	Thermistor value for heated bed. by seatroutfisher	1,597	19	03/21/2016 05:33PM Last Post by dc42
	Newbie need help by tavietbao	868	21	03/21/2016 03:43AM Last Post by dc42
	Problem using temperature over 220C by glompos21	698	3	03/20/2016 12:53PM Last Post by glompos21
	Extruder motor struggles past nozzel by ByteSlinger	1,224	22	03/20/2016 08:13AM Last Post by ByteSlinger

Page 3 of 10 Pages:

1 234 5