Welcome! Log In Create A New Profile

Advanced

Prusa i3 and variants

http://reprap.org/wiki/Prusa_i3 
Subject Views Posts Last Post

Nuts not staying in place....in X axis mounts.

by Flyer
320 4 10/26/2015 05:26AM
Last Post by imqqmi

Ribbed prints

by Nicken83
439 15 10/26/2015 04:58AM
Last Post by Nicken83

Nozzle Drags, Jumps And Messes Up The Print

by ltomov
794 12 10/25/2015 01:28PM
Last Post by ltomov

PLA or ABS not sticking to bed

by Flyer
681 11 10/25/2015 10:35AM
Last Post by tjnamtiw

Part blew up on Prusa i3 motherboard MKS Gen-2Z v1.1

by misterhamin
3,175 23 10/25/2015 09:20AM
Last Post by tow

Help me make this thing quieter.

by msaeger
2,295 22 10/24/2015 11:23AM
Last Post by Nicken83

Quest for the perfect print!

by Slaghton
397 3 10/24/2015 04:28AM
Last Post by Slaghton

Steel i3 Prusa from Createc in Spain

by RRuser
2,874 25 10/23/2015 06:15PM
Last Post by mlaustin66

(SOLVED) Z axis Inches/MM print movement problems, manual/homing fine.

by Slaghton
561 4 10/23/2015 06:11PM
Last Post by Phytone

Just upgraded to 24v heaters

by paultnl
363 3 10/23/2015 10:41AM
Last Post by paultnl

mksbase v 1.3 cannot get lcd controller to power up

by otter5555
980 8 10/22/2015 08:06PM
Last Post by otter5555

Prusa3d.com i3 kit?

by petteri
582 5 10/22/2015 06:02AM
Last Post by petteri

Euroway Prusa I3X Not Starting

by trongey
463 3 10/21/2015 11:44PM
Last Post by trongey

Can't tune Z height "endstop hit: z"

by kareem613
1,025 8 10/21/2015 01:55PM
Last Post by kareem613

Thermistor readings are way off

by Qdeathstar
640 9 10/21/2015 01:07PM
Last Post by Qdeathstar

prusa i3 printing exactly 20% smaller than sliced

by otter5555
350 5 10/20/2015 05:07PM
Last Post by otter5555

Unwarping ABS print

by built350camaro
349 2 10/20/2015 02:36PM
Last Post by widespreaddeadhead

Echo: Active Extruder :0

by Flyer
1,211 3 10/20/2015 12:52AM
Last Post by Flyer

Brand new Prusa i3 (Zonestar) PSU blew up ..

by MrFex
724 8 10/19/2015 05:35PM
Last Post by MrFex

Prusa i3 z axis problem (drives into a bed)

by RaQ007
1,018 13 10/17/2015 06:52AM
Last Post by RRuser

Keeping thermistor in hot end

by Flyer
420 2 10/16/2015 08:39AM
Last Post by paultnl

Prusa I3 Ermes Edition and Megatronics v3.0 problems Attachments

by Hide_the_Tide
582 2 10/16/2015 12:19AM
Last Post by gmckee

Filament jam after every print

by AudaciousTuddle
672 10 10/15/2015 01:37PM
Last Post by AudaciousTuddle

If I plug in a bum thermistor will it kill the board?

by Flyer
572 9 10/15/2015 04:58AM
Last Post by imqqmi

Z axis stop switch lights when X axis motor moved, no power to board???

by Flyer
359 3 10/14/2015 05:53PM
Last Post by Flyer

Designs for i3 with Nema 23s?

by Lenny25
1,163 9 10/14/2015 02:36PM
Last Post by Lenny25

X-axis failure

by killerchimp
350 3 10/14/2015 08:22AM
Last Post by imqqmi

MakerFarm 12" Prusa I3V - my build, usage, and mods   (Pages: 1 2 3)

by itchytweed
4,125 84 10/13/2015 09:01PM
Last Post by itchytweed

Bent threaded rods

by eried
3,095 20 10/13/2015 03:58PM
Last Post by eried

Having a nightmare. Hesine Prusa I3 firmware

by muntahunta
1,488 24 10/13/2015 12:35PM
Last Post by rlschilperoort