Welcome!
Log In
Create A New Profile
Home
>
Machines Organized by Name
>
Prusa i3 and variants
Advanced
Prusa i3 and variants
http://reprap.org/wiki/Prusa_i3
Page 48 of 60
Pages:
46
47
48
49
50
Forum List
New Topic
RSS
Subject
Views
Posts
Last Post
DEFAULT_AXIS_STEPS_PER_UNIT for THSL-300-8D
by
eried
658
3
11/06/2015 02:01PM
Last Post
by
Nicken83
20k thermistor on heatbed
by
Nicken83
363
3
11/06/2015 01:58PM
Last Post
by
Nicken83
LCD is either blank or wont power on
by
jared248371
357
1
11/06/2015 01:34PM
Last Post
by
jared248371
Folgertech Prusa i3 - PC doesn't see the Arduino if Ramps connected
by
SteveSimpson
539
8
11/06/2015 12:12PM
Last Post
by
imqqmi
Hello a little heatbed/Y-Carriage issue.
by
Jarva
798
15
11/06/2015 06:54AM
Last Post
by
RRuser
Set print to always be centered in the middle
by
Kipodolsky
340
2
11/06/2015 06:36AM
Last Post
by
RRuser
Axes will home, but not move with controls or Gcodes
by
Neodavid315
380
1
11/05/2015 07:31PM
Last Post
by
Neodavid315
Prusa i3 rework X Y and Z axes not moving
(Pages:
1
2
)
by
KT1986
2,956
39
11/05/2015 06:43PM
Last Post
by
KT1986
Sunhokey Prusa i3 - Magic Smoke And Death After Connecting USB
by
ltomov
1,230
8
11/04/2015 07:19PM
Last Post
by
CarbonMan
Print goes to shit midway
by
Kipodolsky
404
5
11/04/2015 12:46PM
Last Post
by
Kipodolsky
Help with Electron 3D Printer
by
wittledemon
448
5
11/03/2015 07:44AM
Last Post
by
built350camaro
Y axis jumps 2mm after a few layers
by
Kipodolsky
413
6
11/03/2015 02:26AM
Last Post
by
Kipodolsky
Electron Issue
by
wittledemon
292
9
11/01/2015 09:02PM
Last Post
by
wittledemon
Prusa i3 Hephestos bad quality
by
agoston99
591
6
11/01/2015 03:44PM
Last Post
by
imqqmi
Problems with my wanhao I3
by
SaffaPrinter
733
6
10/31/2015 07:53PM
Last Post
by
otter5555
Extruder Callibration, finding the E mm/sec in Marlin..
by
Flyer
452
4
10/31/2015 02:50PM
Last Post
by
tjnamtiw
Flashing Marlin firmware? Migbot
by
FirstAvenger
742
2
10/31/2015 03:31AM
Last Post
by
imqqmi
Electron 3D Printer Help
by
wittledemon
397
2
10/30/2015 09:36PM
Last Post
by
Qdeathstar
P3Steel V2.5 build blog
by
petteri
630
2
10/29/2015 09:06AM
Last Post
by
RRuser
Best slicer software
by
Nicken83
493
2
10/29/2015 09:03AM
Last Post
by
RRuser
First build problems
by
Nicken83
561
17
10/29/2015 08:40AM
Last Post
by
Nicken83
Electron Prusa i3 E-Motor not moving filament
by
StoneColdLoki
411
3
10/29/2015 12:00AM
Last Post
by
StoneColdLoki
Z axis moves up after print with cura
by
Nicken83
597
3
10/28/2015 11:06AM
Last Post
by
Nicken83
Dual printhead that can print at the same time?
by
kurosame
539
7
10/28/2015 12:54AM
Last Post
by
kurosame
Slic3r upgrade settings for Folgertech Prusa v3
by
Flyer
439
1
10/27/2015 07:52PM
Last Post
by
Flyer
New extruder/hot end
by
AudaciousTuddle
415
7
10/27/2015 11:29AM
Last Post
by
AudaciousTuddle
Sunhokey Prusa i3 hotend/extruder won't stay hot
by
rosebud0911
653
2
10/27/2015 04:32AM
Last Post
by
imqqmi
This offer sounds too good to be true
(Pages:
1
2
3
)
by
Treito
2,108
71
10/26/2015 10:53PM
Last Post
by
tjnamtiw
Folgertech 2020 i3: Massive X shift mid-print
by
cyberkni
638
15
10/26/2015 12:02PM
Last Post
by
Slaghton
Nuts not staying in place....in X axis mounts.
by
Flyer
310
4
10/26/2015 05:26AM
Last Post
by
imqqmi
Page 48 of 60
Pages:
46
47
48
49
50