Welcome! Log In Create A New Profile

Advanced

Prusa i3 and variants

http://reprap.org/wiki/Prusa_i3 
Subject Views Posts Last Post

MOSFET module for PRUSA/RAMPS 1.4 board Attachments

by Erkn
456 5 03/18/2018 12:20AM
Last Post by Marcel K

Changed to M5 Rod, and hearing grinding noise while move z axis from lcd

by bentech4u
123 3 03/17/2018 09:55PM
Last Post by bentech4u
This topic has been moved.

New Prusa Steel Mark 2

by OrballoPrinting.com
    This topic has been moved.

bed leveling help

by daveb693
381 6 03/15/2018 03:57PM
Last Post by tbeaulieu

PID issues

by kenpile
201 2 03/15/2018 03:54PM
Last Post by tbeaulieu

Z Home Position - After I set offset, should G1Z0 go same location?

by tbeaulieu
96 1 03/15/2018 05:41AM
Last Post by tbeaulieu

Auto Bed Leveling and homing issues Attachments

by Throwerrobot
147 2 03/15/2018 05:33AM
Last Post by tbeaulieu

GLASS BED FOR REPRAPGURU DIY RepRap Prusa I3 V2

by woody1940
122 2 03/14/2018 04:11PM
Last Post by jpristel

FIXED!(hopefully) Melzi 2.0 dreaded LCD two lines of death boot-up issue.

by Gatchaman
105 1 03/14/2018 07:11AM
Last Post by Gatchaman

Build the prusa mk3 regular size or build it witha bigger print volume?

by Schwartzer
178 3 03/08/2018 02:28AM
Last Post by dc42

Wiring bltouch with Anet A8

by Giovanni62
981 4 03/07/2018 11:50AM
Last Post by Jax

Scratch build PRUSA MK3 slightly larger

by Schwartzer
229 7 03/07/2018 05:13AM
Last Post by Schwartzer

New Melzi Board Help???

by leonnisae
191 1 03/03/2018 09:11PM
Last Post by leonnisae

Upgrade to Marlin 1.1 Auto Home Issues Attachments

by daankie
176 4 03/03/2018 03:55PM
Last Post by SteveRoy

REPRAPGURU - Prusa i3 Kit - Where does the Extruder fan plug into? Attachments

by tomoneill1991
173 4 02/28/2018 11:04PM
Last Post by SteveRoy

Noise on x axis with new LM8UU 24mm bearings Attachments

by Lon
292 13 02/28/2018 12:49PM
Last Post by Lon

Strange z axis ticking

by Focussys
146 6 02/27/2018 06:33AM
Last Post by daankie

REPRAPGURU - Prusa i3 Kit - Heated Bed fatal error when running Fan > 50%

by tomoneill1991
164 3 02/26/2018 03:24PM
Last Post by tomoneill1991

Trying to find a proper Heating Block/Heat Cartridge for my MK10-based Wanhao i3

by Cyber Akuma
154 1 02/22/2018 09:29AM
Last Post by Cyber Akuma

Anet A8 Firmware upgrade question

by Imagyne
580 3 02/21/2018 05:34PM
Last Post by jaded

Prusa i3 XL not able to reach [email protected]

by kjakobczyk
154 5 02/19/2018 01:32AM
Last Post by o_lampe

TT -->Thermal Runaway

by dibia
139 1 02/18/2018 11:20PM
Last Post by dibia

Einsy Rambo Tuning problems

by lorenjz
154 3 02/17/2018 07:44AM
Last Post by lorenjz

Filament stuck

by BobK
155 7 02/15/2018 05:15AM
Last Post by BobK

Tevo Tarantula firmware update Attachments

by mjo3
319 4 02/14/2018 08:16PM
Last Post by Roberts_Clif

ABS melting on the heated bed at 110 degree

by kjakobczyk
199 11 02/14/2018 08:41AM
Last Post by kjakobczyk

2 Good years and now 60% size prints

by Helihead
164 5 02/13/2018 05:08PM
Last Post by Helihead

Help getting Folger Prusa going. Attachments

by Ecky
166 5 02/13/2018 05:58AM
Last Post by Ecky

MKS Gen 1.4

by bbondura
153 2 02/12/2018 10:08AM
Last Post by Roberts_Clif

Original Prusa i3 Mk2s or Mk3 or......

by Paulgwat
442 3 02/12/2018 08:48AM
Last Post by stamos