Welcome! Log In Create A New Profile


Prusa i3 and variants

Subject Views Posts Last Post

Object height lower than expected in spite of correct calibrated z axis.

by atugrulokur
41 2 03/23/2018 06:36AM
Last Post by MCcarman

Extruder skipping in a pattern Attachments

by muntahunta
299 16 03/21/2018 06:41AM
Last Post by arturmora

How to identify hardware components?

by mitzy
1,430 9 03/20/2018 04:54PM
Last Post by Craigk47

Trying to make my Wanhao I3 Heater Cartridge easily-detachable, can't figure out wire gauge for connectors

by Cyber Akuma
54 4 03/20/2018 03:07PM
Last Post by garyhlucas

Auto Bed Leveling, adding to existing working printer

by bentech4u
97 4 03/20/2018 01:57AM
Last Post by dc42

MOSFET module for PRUSA/RAMPS 1.4 board Attachments

by Erkn
209 5 03/18/2018 12:20AM
Last Post by Marcel K

Changed to M5 Rod, and hearing grinding noise while move z axis from lcd

by bentech4u
46 3 03/17/2018 09:55PM
Last Post by bentech4u
This topic has been moved.

New Prusa Steel Mark 2

by OrballoPrinting.com
    This topic has been moved.

bed leveling help

by daveb693
307 6 03/15/2018 03:57PM
Last Post by tbeaulieu

PID issues

by kenpile
143 2 03/15/2018 03:54PM
Last Post by tbeaulieu

Z Home Position - After I set offset, should G1Z0 go same location?

by tbeaulieu
43 1 03/15/2018 05:41AM
Last Post by tbeaulieu

Auto Bed Leveling and homing issues Attachments

by Throwerrobot
83 2 03/15/2018 05:33AM
Last Post by tbeaulieu


by woody1940
64 2 03/14/2018 04:11PM
Last Post by jpristel

FIXED!(hopefully) Melzi 2.0 dreaded LCD two lines of death boot-up issue.

by Gatchaman
46 1 03/14/2018 07:11AM
Last Post by Gatchaman

Struggling with Einsy

by lorenjz
201 18 03/13/2018 04:42PM
Last Post by lorenjz

Folger Tech Prusa i3 2020 Review

by samuelmennega
613 9 03/11/2018 07:05PM
Last Post by animoose

Build the prusa mk3 regular size or build it witha bigger print volume?

by Schwartzer
100 3 03/08/2018 02:28AM
Last Post by dc42

Wiring bltouch with Anet A8

by Giovanni62
247 4 03/07/2018 11:50AM
Last Post by Jax

Scratch build PRUSA MK3 slightly larger

by Schwartzer
160 7 03/07/2018 05:13AM
Last Post by Schwartzer

New Melzi Board Help???

by leonnisae
139 1 03/03/2018 09:11PM
Last Post by leonnisae

Upgrade to Marlin 1.1 Auto Home Issues Attachments

by daankie
122 4 03/03/2018 03:55PM
Last Post by SteveRoy

REPRAPGURU - Prusa i3 Kit - Where does the Extruder fan plug into? Attachments

by tomoneill1991
114 4 02/28/2018 11:04PM
Last Post by SteveRoy

Noise on x axis with new LM8UU 24mm bearings Attachments

by Lon
242 13 02/28/2018 12:49PM
Last Post by Lon

Strange z axis ticking

by Focussys
111 6 02/27/2018 06:33AM
Last Post by daankie

REPRAPGURU - Prusa i3 Kit - Heated Bed fatal error when running Fan > 50%

by tomoneill1991
103 3 02/26/2018 03:24PM
Last Post by tomoneill1991

RepRap Guru i3 Printer Kit (Official Thread)   (Pages: 1 ... 4 5 6)

17,688 152 02/26/2018 04:56AM
Last Post by wafflejock

Trying to find a proper Heating Block/Heat Cartridge for my MK10-based Wanhao i3

by Cyber Akuma
92 1 02/22/2018 09:29AM
Last Post by Cyber Akuma

Anet A8 Firmware upgrade question

by Imagyne
211 3 02/21/2018 05:34PM
Last Post by jaded

Prusa i3 XL not able to reach [email protected]

by kjakobczyk
115 5 02/19/2018 01:32AM
Last Post by o_lampe

TT -->Thermal Runaway

by dibia
95 1 02/18/2018 11:20PM
Last Post by dibia