Subject		Views	Posts	Last Post
	Atfer Hbot, go to CoreXY. by zelogik			This topic has been moved.
	In need of Prusa I2 X-Ends by HairLikeFrodo	791	17	09/25/2014 07:52PM Last Post by Shank man
	Let out the Magic Smoke by AjaxOfTheRockies	1,917	12	09/25/2014 01:02PM Last Post by SteveRoy
	F2 fuse burning by polkary	1,017	3	09/25/2014 12:59PM Last Post by SteveRoy
	Stepper Motors by electricviolin	428	2	09/23/2014 09:09PM Last Post by Andrew Smith
	Marlin or me? by Waltermixx	529	3	09/23/2014 11:08AM Last Post by Waltermixx
	Wobbly thin bits by GavinRFuller	516	5	09/23/2014 07:18AM Last Post by GavinRFuller
	moves no more by AjaxOfTheRockies	383	4	09/22/2014 10:53PM Last Post by AjaxOfTheRockies
	First time build by 3dprintingnewb	701	7	09/21/2014 03:39PM Last Post by sloppyprinter
	Prusa I3X Unbox and Build by kwhite	1,773	13	09/21/2014 03:11PM Last Post by sloppyprinter
	Runaway X and Y axes during first print by anvoice	1,278	11	09/21/2014 09:04AM Last Post by anvoice
	Heatbed shuts off after a few seconds on by domtropen	835	5	09/20/2014 09:01PM Last Post by domtropen
	ecksbot printer new chip by Andrewblades	817	8	09/20/2014 12:58PM Last Post by plexer
	Need advice & help building a RepRap gantry style printer by csamsi	1,065	1	09/20/2014 12:29PM Last Post by csamsi
	Reprapers in Warwickshire by chrisfest	1,148	6	09/20/2014 09:04AM Last Post by chrisfest
	Extruder height from bed by tayana	1,053	5	09/20/2014 12:24AM Last Post by tayana
	Where to get the "witbox" extruder for the i3 hephestous by 2987ms	2,587	4	09/19/2014 11:50AM Last Post by plexer
	Newbie Z Axis Issue? by urable2	374	4	09/19/2014 03:05AM Last Post by 3dkarma
	Heat bed troubleshooting by domtropen	467	1	09/18/2014 11:55PM Last Post by domtropen
	Insulating hot end with fiberglass by iira	1,051	2	09/18/2014 12:14AM Last Post by tmorris9
	VERY STRANGE PROBLEM with my 3D printer by concetto.oku	681	4	09/17/2014 07:04PM Last Post by gordonendersby
	Hi and X-axis ends advice - Sloppy Pusa i3 parts... by mr.sneezy	1,308	9	09/17/2014 09:13AM Last Post by stustu242
	New XY table printer - software question by leadinglights	1,395	21	09/17/2014 07:20AM Last Post by leadinglights
	Newbie Prusa i3 calibration issues by want2_3d_print	728	2	09/16/2014 02:44AM Last Post by want2_3d_print
	Reprap Build bed not behaving the way I want by GMTminer	1,020	3	09/16/2014 12:53AM Last Post by GMTminer
	Fill Not Reaching Perimeter by dennis1313	621	3	09/15/2014 05:16PM Last Post by dennis1313
	Marlin by andybratton	468	2	09/14/2014 12:08AM Last Post by Evil Monkey
	Hot bed heated up than cooling down by polkary	1,310	13	09/13/2014 03:43PM Last Post by polkary
	PrestoBot. my own design but it is close to the ordbot design by fbnr	1,538	9	09/12/2014 12:25PM Last Post by gen2eng
	Strange PCU & RAMPS Behavior by stutzman	1,633	11	09/12/2014 01:49AM Last Post by polkary