Subject		Views	Posts	Last Post
	Building a rep rap from scratch by Breadmin	913	1	06/04/2012 11:33PM Last Post by Breadmin
	J-Head Leaking by jonasl	1,912	7	06/04/2012 03:55PM Last Post by akhlut
	MendelMax Done! Few question by jonasl	989	3	06/04/2012 04:43AM Last Post by jonasl
	extruder problem: barrel too tight/narrow? by davidra	845	2	06/04/2012 03:44AM Last Post by nophead
	Does anyone know anything about this Hot End? by Leo94	563	1	06/03/2012 06:10PM Last Post by Leo94
	Want gegs extruder in skp format by gregted	924	6	06/03/2012 08:25AM Last Post by gregted
	nichrome wire instalation by epareja	830	2	06/02/2012 09:21PM Last Post by Mkouri
	Glow in the dark filament by gregted	683	1	06/01/2012 01:27AM Last Post by gregted
	Reprap Parts by Matmo	1,110	3	05/31/2012 03:37PM Last Post by avdwege2003
	What does v2 refer to when people are advertising Prusa printed parts by DavidS	836	8	05/31/2012 11:47AM Last Post by Polygonhell
	Print quality.... by Printeur	700	4	05/31/2012 10:37AM Last Post by Printeur
	servo fight by DARCOM	737	4	05/29/2012 08:57PM Last Post by DARCOM
	newbie - firmware woes by bernbe01	727	6	05/29/2012 12:59AM Last Post by bernbe01
	Heat Sink for Pololu Stepper Driver... by mars bonfire	1,265	3	05/28/2012 07:55PM Last Post by mars bonfire
	Pulley for y-axis / length of y-motor shaft by dslc	968	3	05/28/2012 05:17PM Last Post by dslc
	Need custom marlin for a xy doubleing mod by calebzammit	664	6	05/28/2012 12:46PM Last Post by calebzammit
	Slight z movement by enuro12	586	5	05/27/2012 01:53PM Last Post by enuro12
	Hey all, Johnoly99 saying hi by johnoly99	490	1	05/27/2012 01:38PM Last Post by johnoly99
	Webbing on prints by gregted	626	2	05/27/2012 11:14AM Last Post by Mkouri
	Error codes in sli3er by gregted	1,562	4	05/27/2012 11:11AM Last Post by Mkouri
	Estimated time to print a set of MendelMax 1.0 parts? by 3D2B	1,146	7	05/27/2012 05:35AM Last Post by 3D2B
	I should introduce myself / My machine by Chris the Carpenter	943	8	05/26/2012 06:16PM Last Post by Chris the Carpenter
	RepStrap Recipe? by BeagleSeven	1,864	11	05/26/2012 04:02AM Last Post by gregted
	Extruder hot end not so hot... by Hornet	1,016	4	05/25/2012 05:29PM Last Post by g1r9a6d8y
	Calibration/symmetry advice please by jman	992	8	05/24/2012 10:20AM Last Post by jman
	Ambitious RepRap builder by stefanturcanu.11	1,122	8	05/23/2012 07:59PM Last Post by Sellemann
	Techzone Monotronics, replacing ethernet cable to tip by Yvan	740	5	05/22/2012 10:47PM Last Post by Yvan
	Building an SAE Prusa - Have question by djamwolfe	617	2	05/21/2012 01:43PM Last Post by jimcking
	Maya File compatability? by Nadesican	1,914	4	05/21/2012 04:35AM Last Post by pinkyCrook
	Contacting Makerbot by doctek	561	2	05/18/2012 02:22PM Last Post by johnbiehler