Subject		Views	Posts	Last Post
	How to test stepstick by suciokastro	3,381	9	02/26/2013 01:33PM Last Post by jackiejack
	Is the Soliddoodle 3 a better candidate than EventorBot as a 100 micron printer? by markfarnell	1,212	9	02/26/2013 12:11PM Last Post by xclusive585
	ABS temp by prairiewolf407	664	6	02/26/2013 04:01AM Last Post by prairiewolf407
	Prusa i2 and i3 by michaelborg90	4,876	2	02/25/2013 09:51AM Last Post by ikilledkenny
	Need some help with a prusa buy. by Jakecheramie	768	3	02/25/2013 09:35AM Last Post by juliohcd
	Please assist me with my 6 wire NEMA17 motors. by LordTovar	2,095	3	02/24/2013 05:47AM Last Post by bobc
	Where do I buy EXtruder assemble full ? by thanhliem242	455	1	02/23/2013 09:36PM Last Post by thanhliem242
	Extruder temperature registers 340C when its really ~220C by DanMan	535	4	02/23/2013 12:28PM Last Post by DanMan
	Heated Bed Died on me. by Crispy	658	6	02/22/2013 11:45AM Last Post by akhlut
	Y-axis belt drift by thanos	1,657	29	02/22/2013 06:44AM Last Post by rs7k
	After 1st Print, Motors & Heat are not accessible. by JacktheKnife47	530	2	02/21/2013 05:53PM Last Post by JacktheKnife47
	Reprap Mendel air print issue by knightster35	674	5	02/21/2013 03:11PM Last Post by knightster35
	Print accuracy by bigkahuna	519	2	02/21/2013 02:25PM Last Post by xclusive585
	Ramps 1.4 no voltage on d10 by mfuqua	1,190	3	02/20/2013 11:02PM Last Post by mfuqua
	Does EventorBot answer my prayer for a reliable 100-micron layer printer? by markfarnell	1,657	9	02/20/2013 10:39AM Last Post by xclusive585
	RepRapPro Mendel assembly question by psilva	700	5	02/20/2013 08:14AM Last Post by Pauld
	Newbie by adamlister	760	3	02/19/2013 03:53PM Last Post by reprap_ed
	Extuder with max6675 by alfadex	4,765	27	02/17/2013 08:32PM Last Post by alfadex
	Problem: Skeinforge can't save? by PeteD	899	7	02/17/2013 12:36PM Last Post by Dirty Steve
	Orca 0.2 Skeinforge Configuration by sidgouts	620	3	02/17/2013 04:49AM Last Post by sidgouts
	Where to buy Peek bar by smartroad	1,051	2	02/15/2013 11:52AM Last Post by xiando
	Glue for PLA by joestefano	868	4	02/15/2013 05:31AM Last Post by james glanville
	One-For-All Power Supply? by Jim Gourley	504	2	02/14/2013 09:15PM Last Post by stephenrc
	Y axis assembly and 1 print plate by kickinthethroat	1,102	2	02/13/2013 07:54PM Last Post by kickinthethroat
	Bolt hobbing advice by sbliven	1,034	5	02/12/2013 04:02PM Last Post by sbliven
	Creative Machines J-head hot-ends by dslc	684	1	02/12/2013 08:13AM Last Post by dslc
	Slic3r vs Skeinforge first results by skyte	12,221	12	02/12/2013 02:27AM Last Post by Greg Frost
	RepRap Philip Project by CrazyLynx	1,004	2	02/11/2013 01:58PM Last Post by REPRAP SQUAD
	Buying My First Printer, Need Advice by xcaratacusx	708	12	02/09/2013 11:09PM Last Post by DavidS
	I question about hot ends and filament size.... by [email protected]	505	2	02/09/2013 05:39AM Last Post by nophead