Subject		Views	Posts	Last Post
	UP mini 3d printer by Shugs218	99	1	04/12/2024 02:51PM Last Post by Shugs218
	reccomendations by logic_roar	500	6	03/24/2024 06:36PM Last Post by Demolux_D1
	Looking for info for unknown heater bed by bathal	203	1	03/24/2024 02:04PM Last Post by bathal
	snappy 3 issues? by logic_roar	149	1	03/24/2024 06:28AM Last Post by logic_roar
	Z axis Kinematic or fixed industrial printer by xmen	262	4	03/19/2024 07:41AM Last Post by Demolux_D1
	Crealty CR20 Pro woes by stewils	252	3	02/23/2024 08:29AM Last Post by stewils
	Reprap I3 need help setting up by Maddog	286	3	02/06/2024 05:29PM Last Post by Dust
	thoughts on design by civil	1,432	3	01/17/2024 03:38PM Last Post by VDX
	CoreXY: Non-matching MGN carriages on either side of Y? by DailyFrankPeter	519	2	12/01/2023 04:17PM Last Post by Govahnator
	How to avoid strangled cables in cable chains. by Govahnator	358	2	11/30/2023 08:47PM Last Post by Dust
	Extruders motors will not turn by Nigel Kelly	713	13	11/01/2023 04:44PM Last Post by Nigel Kelly
	Nema23 --> Makerbase --> setup by Arnix	919	4	08/27/2023 12:25PM Last Post by Dust
	Megatronics v3 and RepRapDiscount LCD 12864 by julieng7	3,917	9	08/20/2023 06:30AM Last Post by J.Snijder
	moving axis beyond endstop possition by equipment66	916	1	08/03/2023 02:00AM Last Post by equipment66
	Updated to latest firmware cannot heat nozzle by sgtmrcooperusmc	1,104	6	07/28/2023 04:52AM Last Post by sgtmrcooperusmc
	What Filament to use to replace a Bakerlite part by zurferjoe	1,146	1	07/19/2023 12:35PM Last Post by zurferjoe
	Is it okay to not to use smooth rods in 3d printer by erensatik	1,740	6	06/26/2023 05:31PM Last Post by the_digital_dentist
	M155 logging ADC values by wa3scm	1,788	3	05/11/2023 01:40PM Last Post by wa3scm
	delta xy grinding noise on specific coordinates by muhbb	1,765	1	04/30/2023 07:20PM Last Post by muhbb
	Creality Ender5 pro with REPRAPDISCOUNT FULL GRAPHIC SMART CONTROLLER by mehbstnc	2,071	3	04/16/2023 02:48AM Last Post by mehbstnc
	How to set custom home position and drive directions by oBezruki	2,402	10	04/03/2023 03:06AM Last Post by dc42
	Original BCN3D RepRap BOM/STLs by rwilson	3,473	2	03/09/2023 07:44PM Last Post by NewPerfection
	Core ZXZY Build Log by zxzy_eng	2,894	6	01/25/2023 01:32AM Last Post by zxzy_eng
	Marlin on cheap Arduino clone by rwilson	2,533	5	01/16/2023 12:33AM Last Post by VDX
	Marlin 2.1.1 Configuration.hsettings ignored by walts	2,778	4	11/28/2022 09:01PM Last Post by Dust
	Help Driving Stepper with Raw GCode by dlamet	2,846	5	11/08/2022 10:57AM Last Post by dlamet
	Steps per mm not updating with new Marlin Flash by dvanommen	11,032	10	10/29/2022 09:50AM Last Post by Dust
	Stepper does not work with one driver, others do by flomei	2,916	3	10/23/2022 08:37AM Last Post by flomei
	Omni3d Rapcraft 1.4 heatblock tightens right down to heatsink by sundaycrunk	3,366	2	10/03/2022 06:17PM Last Post by rq3
	Job Well Done by Ndv19	3,329	2	09/30/2022 02:57AM Last Post by VDX