Welcome! Log In Create A New Profile

Advanced

GCODE, Software e Firmware

Il codice è la genesi dei nostri oggetti da stampare. 
Page 35 of 53    Pages: FirstPrevious3334353637NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Buzzer non funziona, il beep non si sente   (Pages: 1 2)

by etna953 		1,465 57 03/22/2016 05:12AM
Last Post by jonatan75

Piatto funzionante in ON-OFF e non PWM

by gigillo 		251 3 03/21/2016 06:05PM
Last Post by gigillo

Tempo Stimato di Stampa 0:00:000 Attachments

by luca84 		366 5 03/21/2016 09:50AM
Last Post by luca84

tempo stimato cura con repetier host

by bilanciamist 		1,016 14 03/21/2016 09:49AM
Last Post by luca84

FULL GRAPHIC LCD 12864 su MEGATRONICS V3 Attachments

by Sammy76 		782 9 03/20/2016 03:41PM
Last Post by scorpion74

Inizio stampa

by CanesFAB 		274 3 03/15/2016 05:31AM
Last Post by CanesFAB

Informazioni display

by Sammy76 		308 4 03/14/2016 06:12PM
Last Post by MagoKimbra

problemi configurazione Cura Attachments

by michele1982 		330 2 03/11/2016 06:52PM
Last Post by michele1982

Simplify3d e vasi Attachments

by Adryzz 		454 6 03/11/2016 05:14AM
Last Post by Adryzz

Alligator e finecorsa non interrompono [RISOLTO]

by ManuHC 		336 24 03/10/2016 03:59AM
Last Post by ManuHC

problema lettura sd

by stef.96 		582 8 03/09/2016 04:22AM
Last Post by giggi

10000 metri di filo a chi risolve questo problema

by stef.96 		370 2 03/09/2016 04:21AM
Last Post by giggi

Slic3r - configurare supporti

by bebbbo 		923 2 03/08/2016 07:54AM
Last Post by M_a_X_Italy

Dritta sutemperature stampa e tempo minimo layer su CURA ENGINE

by michele1982 		506 3 03/07/2016 09:57AM
Last Post by immaginaecrea

Errore avr-gcc

by ManuHC 		585 16 03/04/2016 02:50PM
Last Post by Deltone

Impostazione "segment per second" Attachments

by Gex 		607 3 03/03/2016 03:46AM
Last Post by Gex

porta seriale

by stef.96 		203 1 03/02/2016 05:53PM
Last Post by stef.96

centratura stampa

by stef.96 		231 1 03/02/2016 03:31PM
Last Post by stef.96

Autolivellamento con sensore induttivo - Prusa i3 - AIUTO

by martin986 		1,310 7 03/01/2016 08:38AM
Last Post by M_a_X_Italy

Slic3r angry smiley Attachments

by Suffre 		280 3 03/01/2016 07:10AM
Last Post by Suffre

MK 4.2.5   (Pages: 1 2)

by MagoKimbra 		1,024 46 03/01/2016 03:24AM
Last Post by c128

MarlinKimbra R2 Evo Attachments   (Pages: 1 2)

by tommy88 		1,094 34 02/28/2016 06:02PM
Last Post by tommy88

Doppio Estrusore - FW MK 4.1.2

by Marck80 		294 3 02/28/2016 02:22PM
Last Post by MagoKimbra

mk 4.2.7

by lamerhouse 		336 5 02/28/2016 10:03AM
Last Post by lamerhouse

Marlinkimbra: Problema compilazione togliendo ABL

by Labieno 		217 2 02/28/2016 08:02AM
Last Post by MagoKimbra

Simplify3d supporti

by Micron792 		339 1 02/27/2016 05:32PM
Last Post by Micron792

KISSLICER parametri per stampa Attachments

by Fuma 		1,303 11 02/27/2016 04:42PM
Last Post by 3ntrlab

MarlinKimbra e gestione fine filo

by goryc 		286 2 02/26/2016 07:24PM
Last Post by Nicola P

MarlinKimbra Autocalibration Delta abbandonato

by MagoKimbra 		744 6 02/24/2016 12:51PM
Last Post by Paso

Full Graphics su Ramps 1.4

by edofalcone 		518 3 02/23/2016 07:57AM
Last Post by Surfacemodeler
Page 35 of 53    Pages: FirstPrevious3334353637NextLast