Welcome! Log In Create A New Profile

Estrusori, Hotends, Heated bed, Filamenti, etc.

Sezione dove discutere di materiali di stampa e delle parti calde della nostra stampante 3D. Estrusori, Hotends, Heated bed, trafilatura e materiali (filamenti ABS/PLA/etc)

Page 5 of 24 Pages:

3 456 7

Forum List New Topic RSS

	Views	Posts	Last Post
Variazione peso oggetto stampato by Frankq	698	4	06/28/2017 05:38AM Last Post by Frankq
l estrusore non si muove by mede49	745	3	06/25/2017 11:57AM Last Post by mede49
da quanti volt sono i miei riscaldatori ? (RISOLTO) by Amerigo	700	5	06/23/2017 09:33AM Last Post by Amerigo
Modalità conservazione PLA by Frankq	1,274	8	06/23/2017 05:04AM Last Post by immaginaecrea
Estrusore Bowden 3mm by mr.krash	910	9	06/19/2017 11:08AM Last Post by mr.krash
aaa cercasi filamento giusto by cosplayfrancesco	1,008	15	06/19/2017 06:42AM Last Post by Waxplast
Estrusore water cooled by Dark72	1,023	7	06/11/2017 04:23AM Last Post by immaginaecrea
chiarimento wade extruder by andrea2	833	3	06/03/2017 09:34AM Last Post by andrea2
dopo la stmpa conviene ritrarre il filo? by willy12k	837	2	05/22/2017 06:03PM Last Post by MagoKimbra
Filamenti: Peso Vs Lunghezza by Elstak	6,589	23	05/20/2017 08:17AM Last Post by emyx74
dubbio su all-metal bowden by trik	1,698	23	05/19/2017 07:39AM Last Post by alil2096
interruzione flusso pla by willy12k	804	5	05/12/2017 11:24AM Last Post by bilanciamist
Nuovo progetto "Hotend All Metal" (Pages: 1 2 3 4 5) by immaginaecrea	5,895	147	05/12/2017 10:18AM Last Post by trik
Bed che non completa il riscaldamento by mr.krash	889	10	05/04/2017 04:57PM Last Post by mr.krash
pla bronzo ...quale ? by Amerigo	828	12	05/04/2017 11:55AM Last Post by Elstak
Motore estrusore non va con 0.1 mm by DOM	754	10	05/04/2017 11:40AM Last Post by MagoKimbra
blocco estrusore mk8 su stampe di lunga durata by takeoff_82	1,221	20	05/03/2017 06:13AM Last Post by takeoff_82
Stampa PA (poliammide - nylon) by beppexx80	893	7	04/27/2017 01:59PM Last Post by Elstak
Stampa ABS su piatto in vetro by ninjamcrew	3,695	19	04/27/2017 04:02AM Last Post by korrado
Modifica firmware repetier per relè by 1Classe	685	4	04/25/2017 02:39AM Last Post by MagoKimbra
Temperature crescono continuamente by DOM	999	26	04/19/2017 07:29AM Last Post by DOM
Heated bed alligator board by lexering1988	858	16	04/05/2017 12:55PM Last Post by lexering1988
Retrazione mk8 direct lenta by loscorpione	749	4	04/03/2017 11:51AM Last Post by Elstak
levigatura ABS con acetone by settore7G	960	5	03/23/2017 05:57AM Last Post by immaginaecrea
Doppio estrusore o singolo con convogliatore di flusso? by Salvatore94	1,645	22	03/23/2017 05:43AM Last Post by immaginaecrea
Che hot end scegliere by eviljeff	1,205	7	03/19/2017 12:54PM Last Post by eviljeff
tube stop dell'hotend by settore7G	816	11	03/16/2017 10:58AM Last Post by settore7G
Filamento Spezzato by narcy	804	4	03/13/2017 03:16PM Last Post by narcy
temperatura Hotend che sballa by Micron792	777	8	03/10/2017 05:18PM Last Post by Micron792
estrusore perde passi a metà stampa by mirki97	785	5	03/08/2017 04:38PM Last Post by Elstak

Page 5 of 24 Pages:

3 456 7

Estrusori, Hotends, Heated bed, Filamenti, etc.

Nuovo progetto "Hotend All Metal" (Pages: 1 2 3 4 5)