Welcome! Log In Create A New Profile

Elettronica e meccanica

Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc.

Page 42 of 54 Pages:

40 414243 44

Forum List New Topic RSS

	Views	Posts	Last Post
Stampante con motori DC ed elettronica (molto) low cost by ApBrandy	2,906	17	12/09/2014 09:14AM Last Post by ApBrandy
costruzione prusa i2 maggiorata by michele1982	532	3	12/07/2014 10:53AM Last Post by emyx74
Quale elettronica montare by monte.m79	475	2	12/07/2014 10:39AM Last Post by emyx74
scorrevolezza cuscinetti lm8uu by botoxxx	3,558	18	12/07/2014 09:55AM Last Post by pivan
Motori bloccati by ghirap	389	3	12/07/2014 09:04AM Last Post by ghirap
Curiosità estrusore by polbo	592	11	12/06/2014 03:45PM Last Post by enricodare
Problema schermo lcd che diventa illeggibile by AndreaG	557	3	12/06/2014 06:49AM Last Post by AndreaG
Fatto il danno! by michele1982	509	6	12/05/2014 05:03PM Last Post by Fedus82
Quale sistema scegliere per una nuova stampante??? by monte.m79	378	2	12/05/2014 12:24PM Last Post by mic
frame prusa i3 rework by all50	565	9	12/03/2014 12:22PM Last Post by all50
Meccanica , quale ? by piombazzo	345	4	12/03/2014 06:35AM Last Post by maximogti
3drag collegare lcd 12864 con sd by catoplepa	2,403	7	12/02/2014 07:45PM Last Post by catoplepa
Si può usare una alternativa ad arduino per una Prusa i2?... (Launcpad tiva c) by johnsurf	604	13	12/02/2014 01:55AM Last Post by lion_heart78
sbalzo di tensione by Surfacemodeler	354	6	12/01/2014 06:56AM Last Post by Surfacemodeler
Elettronica e consigli per prusa i2! by johnsurf	350	4	11/29/2014 01:38AM Last Post by Simone98
Cuscinetti Lineari Cinesi LM8UU - LM10UU - LM16UU by Anonymous User	516	3	11/28/2014 10:23AM Last Post by Anonymous User
problema prusa i3 by MANE464	642	7	11/28/2014 07:54AM Last Post by maximogti
Problema Motore Asse Z e Endstop by domeman99	1,157	10	11/27/2014 02:47PM Last Post by Dandy
Ingranaggi E Trasmissione Piccola distanza by Anonymous User	354	4	11/27/2014 09:26AM Last Post by mic
Costruire un asse X rigido per cnc da parti reprap by RomanelliAlessio	2,571	13	11/25/2014 11:39AM Last Post by Anonymous User
Ingranaggio di rinvio Y Prusa i3 rework by DeAndreon	814	15	11/24/2014 11:40AM Last Post by Sorbo
Minitronics uff! by emyx74	694	4	11/24/2014 05:28AM Last Post by emyx74
orientamento endstop ottici by angelboss	488	3	11/23/2014 02:07PM Last Post by angelboss
full graphic smart controller by nanigago	617	4	11/23/2014 11:10AM Last Post by bilanciamist
come ripristinare endstop? by SPINA	1,318	7	11/21/2014 04:22PM Last Post by SPINA
Estrusore Rostock su Prusa by gcittadella	411	3	11/21/2014 11:51AM Last Post by gcittadella
smart lcd control by homer07	401	12	11/20/2014 01:50AM Last Post by homer07
x-end con anti wobble incorporato by michele1982	430	2	11/18/2014 04:33PM Last Post by enricodare
hotbed pin diventa caldo by erictondelli	348	3	11/17/2014 05:48AM Last Post by bilanciamist
piano riscaldato elettrico/software by erictondelli	333	1	11/17/2014 05:24AM Last Post by erictondelli

Page 42 of 54 Pages:

40 414243 44