Welcome! Log In Create A New Profile

Advanced

Problemi e qualità di stampa

Avete appena stampato un cubo ed è venuto fuori un prisma? Volete un parere sulla qualità della stampa? Chiedete consiglio qui.
Se siete agli inizi non chiedete qui ma nella sezione dedicata ai principianti. 
Page 37 of 42    Pages: FirstPrevious3536373839NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

problema corrispondenza misure su cornici Attachments

by fr4nc3sco 		640 8 07/05/2014 10:51AM
Last Post by amario57

Movimenti a scatti!

by Ziko 		528 5 07/04/2014 07:17PM
Last Post by 3ntrlab

Problema asse Z prusa i3 [Risolto] Attachments

by Darckan85 		3,489 20 07/03/2014 09:32AM
Last Post by Darckan85

Estrusione insufficiente??

by almaro 		787 13 07/01/2014 08:17AM
Last Post by lion_heart78

spostamento asse y Attachments

by Surfacemodeler 		544 16 06/27/2014 03:53PM
Last Post by Nicola P

Precisione piano di stampa

by Ch4OSm4n 		1,581 20 06/27/2014 03:31PM
Last Post by Ch4OSm4n

Dubbio sul modello stl dell'estrusore [Risolto]

by mike114 		483 7 06/26/2014 08:16AM
Last Post by sipperton

Impostare altezza layer [Risolto]

by vserena82 		1,421 9 06/25/2014 08:39AM
Last Post by vserena82

Ugello che fila

by Sammy76 		379 3 06/24/2014 08:41AM
Last Post by Sammy76

Buchi e imperfezioni Attachments

by andresdanni 		430 2 06/23/2014 10:54AM
Last Post by bertnick

Aiuto! sad smiley centraggio e pezzi che si muovono

by jack_04 		338 4 06/23/2014 09:13AM
Last Post by sipperton

Stampa Calibrationbox : non ne vengo piu fuori Attachments

by Sammy76 		886 28 06/22/2014 10:15AM
Last Post by Sammy76

Problema asse z

by Napolitanodiberlino 		446 17 06/18/2014 02:02PM
Last Post by Napolitanodiberlino

angoli non perfettamente lineari Attachments

by amario57 		473 8 06/18/2014 11:51AM
Last Post by amario57

stampa particolare Attachments

by amario57 		471 13 06/17/2014 03:02PM
Last Post by amario57

Problema stampa imprecisa

by antony95 		582 2 06/17/2014 05:22AM
Last Post by Nicola P

Prima prova Attachments

by Tester 		977 24 06/16/2014 04:37PM
Last Post by Tester

L'hotend si blocca

by rdware 		2,117 22 06/16/2014 11:07AM
Last Post by bertnick

Problema di stampa Attachments

by Lemonz 		861 23 06/15/2014 03:19PM
Last Post by Lemonz

Problema asse Y minitronics

by Darckan85 		368 2 06/15/2014 04:51AM
Last Post by Nicola P

asse z non funzionante   (Pages: 1 2)

by marcogeraldi 		1,572 34 06/14/2014 01:00PM
Last Post by marcogeraldi

Problema fin dalla nascita di questa stampante Attachments

by vitelli 		873 22 06/13/2014 05:17PM
Last Post by Danio Bonello

Problema : Non estrudo abbastanza

by Shraulinger 		434 8 06/12/2014 02:23PM
Last Post by immaginaecrea

Rostock, aumentare la qualità Attachments

by Day_sleeper 		390 1 06/11/2014 09:40AM
Last Post by Day_sleeper

stampa..."screpolata"

by revega 		476 4 06/11/2014 03:08AM
Last Post by bertnick

prusa i3 non funzionante

by marco97 		708 6 06/09/2014 11:01PM
Last Post by NormandC

brim basso, primo layer alto

by mrlove 		528 5 06/09/2014 05:13PM
Last Post by mrlove

ABS fa perdere passi dell'estrusore

by zasf 		724 7 06/09/2014 04:30PM
Last Post by zasf

Raccordo idraulico, riuscite a stamparlo? Attachments

by zasf 		504 3 06/09/2014 03:35PM
Last Post by zasf

stampa inclinata

by ugo3d 		675 20 06/09/2014 06:29AM
Last Post by ugo3d
Page 37 of 42    Pages: FirstPrevious3536373839NextLast