Welcome! Log In Create A New Profile

Advanced

Problemi e qualità di stampa

Avete appena stampato un cubo ed è venuto fuori un prisma? Volete un parere sulla qualità della stampa? Chiedete consiglio qui.
Se siete agli inizi non chiedete qui ma nella sezione dedicata ai principianti. 
Subject Views Posts Last Post
Sticky

►►►► LINEE GUIDA E REGOLE PER UN USO CORRETTO DEL FORUM ◄◄◄◄ Da leggere! Segnalate ai moderatori le discussioni da chiudere - LE REGOLE VANNO LETTE E APPLICATE!

by Gordie
1,749 1 03/09/2014 05:22AM
Last Post by Gordie

Problema aggiornamento firmware Attachments

by Loner
70 2 08/19/2017 01:11AM
Last Post by c11610o

Problema geetech

by FireOwl
170 13 08/17/2017 05:20AM
Last Post by Luca_Benedetto

stampa 3d con fili Attachments

by elvisq
412 12 08/14/2017 12:30AM
Last Post by elvisq

Thermal Runaway e ventola Turbo

by brunosso
198 4 08/04/2017 02:35AM
Last Post by MagoKimbra

Errore caricamento firmware

by Stefano_chi
361 27 07/31/2017 08:53AM
Last Post by MagoKimbra

Tempi di stampa errati

by giuseppegrassano
306 5 07/29/2017 12:47AM
Last Post by Elstak

addrizzare il filamento durante la sbobinatura

by tronicman
373 14 07/16/2017 07:29AM
Last Post by Dariuzzo

3DTouch auto leveling

by vaiper13
296 2 07/15/2017 10:56PM
Last Post by Amerigo

Auto bed Leveling fa solo il controllo centrale

by Leonida9854
323 7 07/05/2017 11:24AM
Last Post by Leonida9854

Modifica altezza piatto Attachments

by tipsy
419 5 06/29/2017 08:04AM
Last Post by tipsy

Interruzione filamento con RepetierHost

by Frankq
319 6 06/29/2017 02:23AM
Last Post by bilanciamist

[Nozzle 0.8mm] Come modificare il modello per aggiungere offset sui fori/alloggi?

by Noisemaker
414 11 06/28/2017 08:21AM
Last Post by Elstak

stampa con pallini e fili Attachments

by Cencio
387 5 06/25/2017 12:08PM
Last Post by Cencio

Strano problema raggio esterno (delta) Attachments

by paglia
343 9 06/14/2017 11:33PM
Last Post by MagoKimbra

Stranezza con il cambio filamento

by tronicman
360 6 06/12/2017 12:10PM
Last Post by tronicman

la mia 3D Benchy Attachments

by giannixful
434 6 06/11/2017 01:48AM
Last Post by giannixful

Vite sinistra asse z R2 Evo

by Trivalb
172 12 06/10/2017 02:25PM
Last Post by Trivalb

Stampa da migliorare ancora

by Salvatore94
349 3 06/10/2017 01:33AM
Last Post by immaginaecrea

Come livellate il piano?

by alex27riva
473 8 06/09/2017 02:47PM
Last Post by tronicman

Le superfici diagonali cedono, dove sto sbagliando? Attachments

by MikyCk
260 13 06/09/2017 12:18AM
Last Post by Noisemaker

Scritte incassate , come stamparle?

by claustro
434 7 06/08/2017 03:37AM
Last Post by Noisemaker

wobble

by matteo2437
478 21 06/02/2017 02:29AM
Last Post by FoxMar

problemi montaggio convogliatore 2 vie R2 EVO

by Yantar
429 5 05/30/2017 11:07AM
Last Post by Yantar

Temperatura estrusore che cala durante la stampa

by khris81
332 3 05/30/2017 01:42AM
Last Post by khris81

Autobed level sensore non si ferma

by Stephen_Wing
357 6 05/25/2017 09:34AM
Last Post by Stephen_Wing

Repetier host fatal error

by khris81
326 9 05/25/2017 12:22AM
Last Post by Erik83

Primi leyers non vengono bene

by Kacro
394 8 05/22/2017 11:58AM
Last Post by Kacro

Qualità di stampa scarsa

by khris81
464 18 05/17/2017 01:49AM
Last Post by bilanciamist

Filo Alfa problemi Attachments

by eviljeff
475 16 05/15/2017 02:32PM
Last Post by eviljeff

Extrusion width e brim Attachments

by Doni90
407 5 05/13/2017 11:37AM
Last Post by alil2096