Welcome! Log In Create A New Profile

Tantillus

http://www.reprap.org/wiki/Tantillus

Page 4 of 12 Pages:

1 2 345

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Tantillus resolution and comparison to other printers by menandore	3,834	15	02/13/2014 08:10AM Last Post by HaDe
	Banding and failed/successful hacks to resolve it by willworkforplastic	5,460	21	02/13/2014 03:14AM Last Post by willworkforplastic
	Sourcing Tantillus Parts by LucasGelf	1,882	13	02/12/2014 09:45AM Last Post by flemming
	Expanding the Tantillus Printed Version by LucasGelf	1,338	4	02/11/2014 11:50AM Last Post by Sublime
	reprap.me J-head back pressure by blabberjack	1,829	9	02/11/2014 01:15AM Last Post by wingnut
	Expanding the lasercut case? by tschmid	995	3	02/08/2014 09:39PM Last Post by tschmid
	1.75mm extruder mod by LucasGelf	1,279	3	02/07/2014 09:03AM Last Post by LucasGelf
	1.75mm Extruder by LucasGelf	1,157	1	02/06/2014 10:02PM Last Post by LucasGelf
	Hobbed bolt by Nick101	1,146	4	02/04/2014 04:52PM Last Post by Sublime
	Motor Question by Chrisp	838	2	02/04/2014 04:51PM Last Post by Sublime
	Extruder too tight? by maik	3,056	12	01/30/2014 01:16PM Last Post by AGStumps8807
	Trouble printing motor gear by maik	1,094	4	01/27/2014 11:16PM Last Post by Robonz
	Calculator size question by flemming	1,138	2	01/24/2014 07:21PM Last Post by Sublime
	Printing Tantillus extruder by Robonz	1,108	3	01/23/2014 11:54AM Last Post by Sublime
	Kisslicer by Happycamper	4,614	11	01/22/2014 12:47PM Last Post by Happycamper
	Tantillus heated bed using aluminium clad element by Robonz	1,721	7	01/20/2014 10:12PM Last Post by Robonz
	Print Issues by Happycamper	866	8	01/20/2014 12:08PM Last Post by Happycamper
	Alignment issues by maik	1,025	6	01/15/2014 04:00AM Last Post by Sublime
	Tantillus Case printed in one shot by beverageexpert	1,119	4	01/14/2014 02:45PM Last Post by Sublime
	Belt drive extruder by wingnut	1,810	8	01/13/2014 04:42PM Last Post by Sublime
	Alas printing, well sorta by flemming	1,519	16	01/08/2014 12:44AM Last Post by Robonz
	Z wobble hack - printed part by Robonz	3,293	13	01/07/2014 01:54PM Last Post by wingnut
	New build extruder troubles by flemming	1,109	6	01/04/2014 06:32PM Last Post by flemming
	Making Embossed letters stand out on models by willworkforplastic	1,478	3	12/28/2013 10:34PM Last Post by willworkforplastic
	Broken extruder by maik	947	6	12/28/2013 07:47PM Last Post by willworkforplastic
	Build plate dimensions by wingnut	1,254	6	12/24/2013 01:41PM Last Post by Sublime
	Minimum Temp by wingnut	990	8	12/19/2013 03:58PM Last Post by Sublime
	Sparse spots on layers by maik	896	2	12/19/2013 01:45AM Last Post by Sublime
	Tantillus Rods by slashflame	1,409	4	12/18/2013 09:42AM Last Post by Ataraxia
	X AXIS on E1 RAMPS 1.4 sprinter firmware by ale92	1,128	2	12/17/2013 05:11PM Last Post by davidefa

Page 4 of 12 Pages:

1 2 345