Welcome! Log In Create A New Profile

Advanced

Repetier

Subject Views Posts Last Post

Garage to cold ?

by Replace
286 4 01/20/2017 06:12AM
Last Post by obewan

Repetier Host & Diamond hot end

by kd6hq
305 3 01/19/2017 04:19PM
Last Post by kd6hq

Serial COM Error

by softdeth
388 2 01/04/2017 03:00AM
Last Post by repetier

crashes in bed

by DDave62
358 1 01/01/2017 11:29AM
Last Post by DDave62

Heated bed enabling

by biscuits
5,525 9 12/27/2016 08:15AM
Last Post by troy8hohulin

Repetier host plugin for CNC

by ahd71
2,186 7 12/26/2016 02:39AM
Last Post by justcurious

Prusa i3, Z probe, repetier firmware and problems... grinning smiley

by Mister Fab
378 3 12/24/2016 02:41AM
Last Post by Mister Fab

Newbie help with Repetier Host issue?

by PNW_steve
348 1 12/16/2016 10:45AM
Last Post by PNW_steve

Repetier Host and AzteegX5/Smoothie

by sheepdog43
860 5 12/15/2016 01:12AM
Last Post by repetier

Sentinel in kickstater

by Replace
343 1 12/09/2016 10:33PM
Last Post by Replace

Extruder heater seems to turn off after printing starts Attachments

by bartlee45
384 2 12/04/2016 06:03AM
Last Post by RFZ

<Slic3r> Invalid extrusion width (too large)?

by vikrbh
473 4 12/04/2016 05:51AM
Last Post by RFZ

repetier: stops randomly   (Pages: 1 2)

by Darki
2,931 42 11/30/2016 11:11AM
Last Post by pdtechBigBot

Switch to RADDS and axes don't move

by mikefazz
280 2 11/25/2016 11:54PM
Last Post by mikefazz

Ultratronics board + RaPS128 + Repetier configurator = the good combination

by Pi-Wi74
800 2 11/22/2016 02:41PM
Last Post by MagoKimbra

Home position setting

by RGN01
365 1 11/19/2016 02:42PM
Last Post by RGN01

Api Key?

by Jfox
383 2 11/16/2016 11:24PM
Last Post by repetier

Gcode initiated pause

by Replace
473 3 11/16/2016 11:22PM
Last Post by repetier

Repetier-Host crashes randomly on Linux Mint

by David J
1,561 16 11/16/2016 11:21PM
Last Post by repetier

Repetier firmware

by derhesse2002
322 1 11/13/2016 02:50PM
Last Post by derhesse2002

Problems with thin walls Attachments

by Supermec
397 1 11/05/2016 09:09AM
Last Post by Supermec

Repetier Firmware

by khondoke
581 3 10/17/2016 05:25PM
Last Post by Roger123D

Error: Apos y steps

by Kelvin Nhut
300 1 10/16/2016 11:43AM
Last Post by Kelvin Nhut

Procedure to calibrate Z-home / limit. Repetier Host.

by lmr
563 3 10/15/2016 01:49PM
Last Post by RFZ

Error Extruder 0

by Ma_tits
335 3 10/14/2016 08:54PM
Last Post by Roger123D

manual controll in Repetier

by Phirockz
469 2 10/14/2016 08:48PM
Last Post by Roger123D

slicing weirdness

by bulwynkl
240 2 10/14/2016 08:38PM
Last Post by Roger123D

Jam detection

by scuba
3,931 11 10/13/2016 08:32AM
Last Post by Replace

Help Da Vinci 1.0 no longer printing

by Chromewrecker
223 2 10/10/2016 03:10PM
Last Post by Chromewrecker

software Z=0 adjustment in firmware/host

by RFZ
288 1 10/10/2016 01:35PM
Last Post by RFZ