Subject		Views	Posts	Last Post
	Lip around perimeter near top by nebbian	1,637	25	12/11/2015 06:19AM Last Post by BoByS
	Not printing uniformly by GuerillaEngineer	652	9	12/11/2015 03:29AM Last Post by Anonymous User
	Circles don't come out circular (Prusa i3) by Apple-	1,218	4	12/10/2015 06:47PM Last Post by elwood127
	Prusa i3 ruining my life (again) by davidbananas999	710	9	12/10/2015 06:40PM Last Post by elwood127
	Extruder Jamming by pyromanci	834	6	12/10/2015 06:12PM Last Post by elwood127
	Sloppy edges on vertical surfaces Prusa I3 by Ralphy	930	14	12/10/2015 05:57PM Last Post by elwood127
	Turn off PID in marlin by rizulthkr	398	3	12/10/2015 04:18PM Last Post by Downunder35m
	Wrong X and Y position after Auto leveling by gurmeet.athwal	3,694	13	12/08/2015 05:16PM Last Post by xile6
	Under or over extrusion? by IG88	2,306	5	12/08/2015 11:27AM Last Post by IG88
	Walls grow higher than infill? by pengpengpete	1,238	12	12/08/2015 06:38AM Last Post by RRuser
	Filament Runout Sensor without LCD-Panel? by Eistee	762	1	12/08/2015 06:11AM Last Post by Eistee
	Retraction problem (not retracting)_Prusa i3 by Smatta	1,373	8	12/07/2015 05:43AM Last Post by Downunder35m
	Extruder issues with ABS by BoByS	1,786	7	12/06/2015 03:11PM Last Post by BoByS
	Random Movements by balbers	1,741	12	12/05/2015 10:26PM Last Post by balbers
	Prusa i3 ruining my life by davidbananas999	901	10	12/05/2015 06:22AM Last Post by RRuser
	Filament jamming by nkuck	328	6	12/05/2015 04:31AM Last Post by Downunder35m
	Delta printer wont raise on z axis during print by Sk8rseth	721	2	12/05/2015 03:50AM Last Post by o_lampe
	Power / LCD Flickering during printing by NorcoT	4,821	11	12/04/2015 07:39PM Last Post by 3DPrintAmazing
	Rambo Dual Extrusion Hot ends heat slowly and at different rates by zborschuk	959	12	12/03/2015 08:17AM Last Post by zborschuk
	Weird Layer Shifting by Hauser	733	6	12/01/2015 08:40AM Last Post by RRuser
	water cooled extruder: what do you think? by koenejet	862	13	11/30/2015 06:54PM Last Post by koenejet
	Infill gaps and Parts to fit by mikh3x4	2,007	25	11/30/2015 05:14PM Last Post by Darmach
	Mono Mendel issues by nikhil	408	2	11/30/2015 02:02PM Last Post by gurz4517
	Small prints lift off bed and stick to nozzle. by kenblu24	1,130	4	11/30/2015 03:36AM Last Post by dintid
	Ovals instead of circles.. by papabur	473	1	11/29/2015 01:20PM Last Post by papabur
	Quality of Filament by awesomed1	631	5	11/28/2015 11:55PM Last Post by awesomed1
	ABS is getting out from the gap by microspace	716	9	11/27/2015 10:59PM Last Post by microspace
	Print greats then stops by Helihead	690	12	11/27/2015 10:31PM Last Post by Helihead
	Ripples on X and Y axis by jsaiko	1,459	11	11/27/2015 01:48PM Last Post by SlowFoot
	It's just too cold! by KillerDave	1,489	19	11/27/2015 04:03AM Last Post by DjDemonD