Subject		Views	Posts	Last Post
	Head Stops Mid Print+Network Crash by drentsoft	404	5	05/25/2016 07:53AM Last Post by drentsoft
	Minimizing z axis movement by trbjr	248	2	05/25/2016 12:34AM Last Post by elwood127
	Delta Printer Hot End Unpredictably Jamming into Print </3 (Cool Stepper Motors, Cool Drivers, Smooth Rails,Tight Belts) by TheShrubPatrol	529	3	05/24/2016 08:25PM Last Post by JamesK
	Cura and move axis by TommyF	863	3	05/24/2016 05:30AM Last Post by TommyF
	DRY FILMENT STORAGE by XR750	895	10	05/24/2016 04:05AM Last Post by the_digital_dentist
	ramps 1.4 ( d08 - d10 no respond) by 3dfbomb	395	4	05/23/2016 09:40PM Last Post by JamesK
	Poor top layer quality by Basell	2,981	8	05/23/2016 02:56PM Last Post by Basell
	changing nozzle size to fix extruder blocking/jamming by friarfish	437	3	05/23/2016 12:51AM Last Post by elwood127
	1.75mm filament force on bowden hotend by v1talogy	870	9	05/22/2016 04:31PM Last Post by Srek
	Bad printing by tape	318	2	05/21/2016 05:19PM Last Post by ggherbaz
	Layers and skipping by tim3716	940	11	05/21/2016 02:35AM Last Post by ggherbaz
	blobby and stringy by Lymphomaniac1	683	2	05/20/2016 01:45AM Last Post by Downunder35m
	PETG Filament Crimping In Extruder by mpmumau	1,388	9	05/19/2016 11:35PM Last Post by mpmumau
	Dual Extruder for Pla by 3ddreams	625	6	05/19/2016 01:43PM Last Post by 3ddreams
	kisslicer guidelines for shell width/layer height by friarfish	1,779	6	05/18/2016 11:28AM Last Post by ggherbaz
	printing issues   (Pages: 1 2) by heauxmbru	871	33	05/17/2016 09:27PM Last Post by JamesK
	ABS warping solved (I think) by PixelPusher	667	10	05/17/2016 02:35PM Last Post by Floyd
	ABS print filament folding inside extruder and gets stuck by bw_syl	927	9	05/17/2016 12:03PM Last Post by bw_syl
	Changing E steps by drmaestro	368	9	05/16/2016 07:17PM Last Post by drmaestro
	Some time since last 3D by TommyF	312	3	05/16/2016 03:48PM Last Post by TommyF
	Corners on Circles by peonking	2,377	18	05/15/2016 05:12PM Last Post by sigxcpu
	Extruder not extruding by Jesse D	342	4	05/15/2016 08:35AM Last Post by Jesse D
	Trouble with top layer using PETG by tmorris9	2,330	3	05/15/2016 02:05AM Last Post by Downunder35m
	problem with sticking to the bed by new3dguy	300	3	05/14/2016 04:24PM Last Post by ggherbaz
	[SOLVED] First good, then blobs, then nothing by state	1,050	10	05/14/2016 10:45AM Last Post by state
	Nozzle cools before reaching target by DaveOB	406	8	05/13/2016 07:25AM Last Post by JamesK
	Can't figure out extrusion problem by sergeys	661	30	05/12/2016 08:48PM Last Post by sergeys
	Bad quality by hamid	398	5	05/12/2016 02:41PM Last Post by the_digital_dentist
	pursa i3 build what electronics and fireware is best by chasemn34	374	1	05/11/2016 05:20PM Last Post by chasemn34
	Inductance probe logic detection on ramps 1.4 by dbeck002	308	2	05/10/2016 11:41AM Last Post by stephenrc