Subject		Views	Posts	Last Post
	Prints leaning by blt3dp	1,429	17	02/11/2014 01:38AM Last Post by blt3dp
	Entangling in the extruder by ariza1992	441	4	02/10/2014 09:45PM Last Post by ariza1992
	Layer Printing issues by DoctorWoo	752	12	02/10/2014 07:00PM Last Post by Jc61990
	Print from SD? by Olafur Pa	436	2	02/10/2014 02:47PM Last Post by jbernardis
	Is it possible for an STL to be too complex for Slic3r to handle? by naazrael	929	6	02/09/2014 10:00PM Last Post by KingRahl
	Printing Issue by BlaiddDrwg	507	3	02/09/2014 02:40PM Last Post by BlaiddDrwg
	Gen 6 board motors stops run by danielq	486	2	02/09/2014 06:26AM Last Post by danielq
	First layer not printing (two different printers) by Jc61990	665	5	02/08/2014 08:46PM Last Post by Jc61990
	CURA calibration help! by Floyd	1,484	3	02/06/2014 02:11PM Last Post by Floyd
	Problem printing thin wall objects. by gmh39	3,260	12	02/05/2014 09:27AM Last Post by gmh39
	First 5 layers, wird outline/shell by tintinz	487	1	02/04/2014 05:55AM Last Post by tintinz
	E-steps, Retraction or Extrusion Multiplier by academicdave	1,390	2	02/03/2014 01:39PM Last Post by gmh39
	Little Problems with edges, second layer, infill by 4Stroke	517	1	02/02/2014 09:09AM Last Post by 4Stroke
	Problem with filament restarting after retraction by agirgen	3,143	6	02/01/2014 07:12PM Last Post by Ohmarinus
	PLA printing issues by calad	886	4	02/01/2014 09:03AM Last Post by calad
	extruder pulling filament back and making it bubble and get stuck. by vcazan	1,825	16	02/01/2014 12:12AM Last Post by vcazan
	What is "W" Parameter is Pronterface log.? by reprapnewbie	805	3	01/31/2014 04:13AM Last Post by reprapnewbie
	Print looks wierd. by TRoager	1,318	20	01/30/2014 10:51AM Last Post by TRoager
	Online printing, a growing business ? by rohitbalak	387	1	01/30/2014 05:39AM Last Post by rohitbalak
	Layer Striping by jmarasch	662	8	01/29/2014 10:18PM Last Post by jmarasch
	A 'panic buy' of acetone based nail varnish remover by Alzibiff	2,945	13	01/29/2014 03:29PM Last Post by waste
	the wonders of lemon juice in the sticking of printed parts by waste	5,796	16	01/29/2014 03:19PM Last Post by waste
	Slic3r not slic3ring by bill84	492	5	01/29/2014 03:08PM Last Post by bill84
	Bottom layer not solid by amr_dwarf	702	5	01/29/2014 02:17PM Last Post by amr_dwarf
	Top and Bottom Infill by strat	1,127	6	01/29/2014 03:58AM Last Post by Ohmarinus
	Non-equidistant wavy walls by probonic	545	3	01/29/2014 03:55AM Last Post by Ohmarinus
	Suggestion to improve printing Quality by Alex2099	773	4	01/29/2014 12:50AM Last Post by svalsorim
	Changing filament during print   (Pages: 1 2) by papergeek	11,958	31	01/28/2014 06:10PM Last Post by KingRahl
	First Prints: a lot of problems by thebus	691	2	01/28/2014 03:08AM Last Post by thebus
	Help Calibrating by academicdave	569	1	01/27/2014 01:01PM Last Post by academicdave