Subject		Views	Posts	Last Post
	Corner of my cube test print keeps lifting? by Chapster5	678	5	03/14/2014 09:20AM Last Post by Crewmember
	Any info on Kisslicer? by Jomo	1,630	5	03/13/2014 08:30PM Last Post by Jomo
	Holes with small bump in perimeter by botbuilder	780	6	03/13/2014 06:47PM Last Post by botbuilder
	Problem with 'Stepping' in straight Lines by pelo13	792	8	03/13/2014 02:15PM Last Post by pelo13
	hobbed bolt jumping by hhbhagat	649	10	03/13/2014 01:59PM Last Post by hhbhagat
	Searched everywhere. by gilsah	703	3	03/13/2014 01:37PM Last Post by ShawnT98027
	Oozing streaks during nozzle travel by hennenzac	662	2	03/12/2014 09:51PM Last Post by hennenzac
	Persistent extruder jamming by equinox86	1,073	7	03/12/2014 09:52AM Last Post by equinox86
	help with feeding issue by myk68	391	3	03/11/2014 08:33PM Last Post by waitaki
	Problem printing GT2 pulleys by FlyingLotus1983	1,167	5	03/11/2014 04:47PM Last Post by FlyingLotus1983
	Skipping steps by martinpells	575	2	03/11/2014 03:31PM Last Post by NewPerfection
	LOTS OF BUR ON PRINTS by pingnagan	717	9	03/11/2014 03:35AM Last Post by pingnagan
	Z Ribbing Issue by GtwoK	1,385	10	03/10/2014 09:50PM Last Post by GtwoK
	Finding the right temperature by TheBearF8	2,092	11	03/10/2014 06:56PM Last Post by NewPerfection
	Low Layer Height Issues by ayouden	1,022	13	03/10/2014 08:45AM Last Post by jamesdanielv
	Why is slicer filling in holes by Beoga	2,978	10	03/10/2014 03:53AM Last Post by Beoga
	Layer starting issues by Floyd	514	4	03/09/2014 11:23PM Last Post by Floyd
	Layer Settings by jsluke	472	5	03/09/2014 09:14PM Last Post by cfy7
	first layer printing by carmojos	552	8	03/08/2014 07:53PM Last Post by waitaki
	The part isn't filled in curves by Lmecano	638	4	03/08/2014 01:43PM Last Post by Dirty Steve
	Plastic wire broke ! by Lmecano	719	6	03/08/2014 09:06AM Last Post by Lmecano
	DIYTechShop i3xl Hot End Issue by Psionystic	1,354	3	03/07/2014 11:07PM Last Post by cfy7
	Calibrating by Korri	939	8	03/07/2014 04:04PM Last Post by NewPerfection
	Help me identify fault with my print. by cfy7	585	3	03/07/2014 12:56PM Last Post by cfy7
	Suddenly more and more Warts/Zits (alot) on print surface. (ABS) by Crewmember	1,974	10	03/07/2014 11:09AM Last Post by piercet
	Z axis too short by cfy7	2,074	5	03/07/2014 10:59AM Last Post by cfy7
	Heated Bed Separation by hhbhagat	818	2	03/06/2014 05:37PM Last Post by NewPerfection
	Sudden delamination by mekios	525	3	03/06/2014 03:17PM Last Post by swoozle
	No filament at printing by TheBearF8	600	4	03/05/2014 04:06PM Last Post by NewPerfection
	test cube by gilsah	818	6	03/05/2014 12:16PM Last Post by TheBearF8