Subject		Views	Posts	Last Post
	Part height / thickness question by hennenzac	537	5	04/03/2014 10:14AM Last Post by hennenzac
	Ormerod duet board not connecting by Ninjamandk	295	1	04/03/2014 07:48AM Last Post by Ninjamandk
	Prusa i3 Printing Issues by rabidscorpio	1,312	4	04/03/2014 03:05AM Last Post by waitaki
	x axis skipping by DoctorWoo	833	15	04/02/2014 09:38PM Last Post by soldanr
	ABS and Kapton tape- all the same? or? by maddog7	1,979	21	04/02/2014 05:24PM Last Post by Wvantoorn
	Marlin FW - Printing offset by 10mm on X&Y - Autobed Leveling Used by TAZ427	412	1	04/02/2014 12:17PM Last Post by TAZ427
	Overhang issue by seb_reunion	1,152	8	04/02/2014 06:52AM Last Post by seb_reunion
	Marlin Falure to run Gcode by Velocity	415	1	03/31/2014 08:42PM Last Post by Velocity
	Please help me solve this by jpan	1,607	25	03/31/2014 08:33PM Last Post by jpan
	Filament is stuck, doesnt get transported by JPT	507	7	03/30/2014 02:30PM Last Post by JPT
	printing issues by randyf1965	845	9	03/30/2014 09:28AM Last Post by randyf1965
	I3 xl Extruder Stepper settings by JBaczuk	400	2	03/30/2014 05:26AM Last Post by waitaki
	Mendel starts printing "in the air" by snoller	427	1	03/29/2014 01:26PM Last Post by snoller
	Will not run Gcode Marlin by Velocity	448	1	03/28/2014 07:06PM Last Post by Velocity
	Two Issues, One Print by lukan	791	2	03/27/2014 07:44PM Last Post by lukan
	Bird's nest printing - the dark side of the Force by Reinhold	626	1	03/27/2014 09:16AM Last Post by Reinhold
	Y axis displaced 3mm after printng for 5hrs of 6.5hr prt by monaro	599	5	03/27/2014 06:48AM Last Post by sharque
	Bonding between PLA and ABS by Kenzu	1,224	5	03/27/2014 05:08AM Last Post by Kenzu
	Printing first layer too thin by lwong	1,192	4	03/27/2014 12:39AM Last Post by lwong
	Filament jams - Bulldog XL & E3D by CmdrKeen	1,521	4	03/26/2014 06:24PM Last Post by chewbaccah
	gummy hotend by f3rDz	633	7	03/26/2014 05:58PM Last Post by chewbaccah
	First time 3D printer user... Struggling with ABS and starting layers by Chapster5	1,020	16	03/26/2014 12:45PM Last Post by Chapster5
	Extruder is not extruding properly at first. by nantes	376	2	03/25/2014 07:04PM Last Post by cat.farmer
	Print Speed Issues in Firmware(possibly software) by GrantGabrielson	523	6	03/25/2014 11:25AM Last Post by GrantGabrielson
	spessore ai fori by aurelio	340	1	03/25/2014 11:19AM Last Post by aurelio
	PLA print issues by Thelontin	539	4	03/25/2014 11:12AM Last Post by Thelontin
	Another "Help Me Tune/Diagnose My i3 Print Issue" Thread. by ENRKyle20	836	13	03/25/2014 10:59AM Last Post by ENRKyle20
	Second Layer print issue by Beoga	496	3	03/25/2014 09:47AM Last Post by GrantGabrielson
	AZTeeg X3 Pro Stepper skipping by jhenak	2,315	4	03/25/2014 09:08AM Last Post by bilsch
	ABS layers not sticking. by Scribble	1,900	12	03/25/2014 02:26AM Last Post by Ralf