Subject		Views	Posts	Last Post
	Aligning Dual Extruders? by Chapster5	1,599	8	04/15/2014 04:09PM Last Post by lukan
	Plastic blobs on first layers by LordGG	666	3	04/15/2014 09:38AM Last Post by LordGG
	Z-axis suddenly only moves down by Ohmarinus	809	3	04/14/2014 07:56AM Last Post by Ohmarinus
	Supports a pain in the arse to remove and leaving rough surfaces by Chapster5	502	1	04/13/2014 04:50PM Last Post by Chapster5
	Curling Edges (NOT FIRST LAYER) by zacevans36	717	5	04/12/2014 09:04PM Last Post by zacevans36
	Printrboard Issues (E out of control and other abnormalities) by GrantGabrielson	413	1	04/12/2014 04:54PM Last Post by GrantGabrielson
	Merlin Hotend infill issues by shai	1,016	5	04/12/2014 09:12AM Last Post by Srek
	Hobbed bolt shaving the filament by hhbhagat	1,471	10	04/12/2014 05:04AM Last Post by Srek
	Warped prints on certain shapes by ghobbs	471	4	04/12/2014 01:57AM Last Post by Ralf
	over/under extrusion at the same time? by aruta	1,009	2	04/11/2014 04:57PM Last Post by jm44807
	Hobbed bolt slipping by Archelon	815	4	04/11/2014 09:40AM Last Post by Archelon
	Prusa i3 + ABS by TRoager	9,560	26	04/11/2014 07:31AM Last Post by TRoager
	Importing g-code by hsteven7	817	3	04/10/2014 03:11PM Last Post by hsteven7
	Cold bed adhesion by epicepee	1,170	9	04/10/2014 08:00AM Last Post by konwiddak
	whats up with this print by horizonleatherco	1,087	8	04/09/2014 04:05PM Last Post by maltasev
	direct drive extrusion and consistent flow by bilsch	2,910	12	04/09/2014 02:59PM Last Post by SolidUtopia
	prusa i3 prints outer edge two or three times by psi3000	710	2	04/08/2014 09:11PM Last Post by psi3000
	E3D v5 Clogging by Bharadwaj	1,906	6	04/08/2014 10:11AM Last Post by Bharadwaj
	Artefact at perimeter change by Protoprinter	2,262	9	04/08/2014 02:41AM Last Post by Protoprinter
	Most idiotic/genius idea for bridging/overhangs? by MrDoctorDIV	563	4	04/07/2014 09:50PM Last Post by waitaki
	DRV8825 Weird sounds? by Skunky	1,645	4	04/07/2014 12:16PM Last Post by midebiec
	Printing issues by Trexter67	637	8	04/06/2014 10:00PM Last Post by Trexter67
	On the learning curve- What's this? by Bill Clark	431	3	04/06/2014 08:45PM Last Post by Bill Clark
	extruder geting stuck by pixbranders	358	2	04/06/2014 05:17PM Last Post by 3dkarma
	Cylinders with edges by runninfarmer	433	2	04/05/2014 06:58PM Last Post by Dirty Steve
	Need help to root cause these printing defects by Sumeet	835	4	04/05/2014 04:38PM Last Post by MrDoctorDIV
	Over Extruded Layer? by runninfarmer	558	6	04/05/2014 12:47AM Last Post by runninfarmer
	No extrusion in the middle of print by luka_d	494	5	04/04/2014 08:37PM Last Post by cat.farmer
	Premature Completion of Print by jewberg	497	8	04/04/2014 05:24AM Last Post by waitaki
	Possessed Hotend by lonemedic	481	5	04/03/2014 01:08PM Last Post by lonemedic