Subject		Views	Posts	Last Post
	Infill/Support Problems by OsiViper	428	3	05/12/2014 01:08AM Last Post by NeilRG
	Vase printing issue by kevwal	462	5	05/11/2014 08:05PM Last Post by Dirty Steve
	Huxley Merlin problem? by Pyragira	305	2	05/11/2014 04:51PM Last Post by 3dkarma
	filament diameter - how acurate by Arnold	634	8	05/11/2014 04:14PM Last Post by myk68
	Center changing after auto leveling by randyf1965	384	3	05/11/2014 10:37AM Last Post by pingpouk
	Should heating the hot end take this long? by unknowntothem	1,101	7	05/10/2014 11:47AM Last Post by MrDoctorDIV
	Differences in batches of plastic ? by borupdk	476	3	05/10/2014 06:56AM Last Post by borupdk
	Help fine tuning calibration (ugly 5mm calibration cube) by Eqpirate07	680	4	05/09/2014 04:24PM Last Post by Osios
	Lack of extrusion on layers with less by MrDoctorDIV	660	4	05/09/2014 04:19PM Last Post by MrDoctorDIV
	Hot end and vents completely blocked by Mageri	767	3	05/09/2014 02:27AM Last Post by deals4print
	problem printing in pla by bilsch	1,386	13	05/08/2014 06:35PM Last Post by bilsch
	Thin sections fail by patman	776	6	05/07/2014 11:30PM Last Post by patman
	Filament stopper after 2 hour of printing by Arnold	562	2	05/07/2014 07:34PM Last Post by chewbaccah
	Thin layers on top and bottom by funnytrash	1,114	7	05/07/2014 06:06PM Last Post by waitaki
	Blobby J-head clone on 1.75mm filament, melt chamber too large? by Zedsquared	1,298	3	05/07/2014 10:03AM Last Post by konwiddak
	What size is my Hotend? by MoonTimber	630	3	05/06/2014 03:18PM Last Post by konwiddak
	ABS Print by Osios	1,267	8	05/05/2014 09:53AM Last Post by ecoreprap
	Hotend temperature 736 - real zero by Arnold	780	5	05/05/2014 03:13AM Last Post by Arnold
	Belt loose can't fix by ed328	1,354	5	05/02/2014 06:18PM Last Post by ed328
	Extruder motor is faster than filaments move by Arnold	1,220	10	05/02/2014 06:16PM Last Post by ksk
	Extruder not heating by JarlSagan	1,488	10	05/02/2014 01:21PM Last Post by ksk
	whats your strategy for tuning demensions by Bill Clark	1,034	13	05/02/2014 01:06PM Last Post by Bill Clark
	Rough Prints by tmorris9	1,584	14	05/01/2014 09:37PM Last Post by tmorris9
	Base Layer Problems... by OsiViper	729	11	05/01/2014 07:52PM Last Post by ksk
	Layers not sticking together properly by victorjung	826	4	05/01/2014 06:56AM Last Post by victorjung
	Help setting up a new printer   (Pages: 1 2) by Eqpirate07	1,875	35	04/30/2014 09:45PM Last Post by ooxtcoo
	Printing Layer Error : HELP PLZ! by Janski	458	8	04/30/2014 10:25AM Last Post by Janski
	Z axis stops after a while of very good printing by mgoncalves	786	5	04/30/2014 05:02AM Last Post by deals4print
	Printing with heated bed causes power to cycle on/off by ttttrigg3r	682	8	04/29/2014 08:14PM Last Post by cat.farmer
	Difficulties extruding filament by borupdk	466	3	04/29/2014 07:53PM Last Post by borupdk